A series circuit with R = 10 2, L = 0.1 H and C = %3D %3D 50 µF has an applied voltage V = 50 L0° with a variable frequency. Find the resonant frequency, the value of frequency at which maximum voltage occurs across the inductor and the value of fre- quency at which maximum voltage occurs across the сараcitor.

A series circuit with R = 10 2, L = 0.1 H and C = %3D %3D 50 µF has an applied voltage V = 50 L0° with a variable frequency. Find the resonant frequency, the value of frequency at which maximum voltage occurs across the inductor and the value of fre- quency at which maximum voltage occurs across the сараcitor.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 1PA: You are an electrician working in a plant. A series resonant circuit is to be used to produce a high...

See similar textbooks

Similar questions

A resonant LC circuit is delivering 100 W of power. What is the power value (in watts) at -3dB point?
H.W: A resistor of resistance R-1000 2 is maintained at 17 °C and it shunted by 100 uH inductor. Determine the rms noise voltage across the inductor over a frequency bandwidth of: i) 15.9 kHz Ans: 182 x109 volt ii) iii) Ans: 9.22 x10-8 volt Ans: 2.34 x10-6 volt 159 kHz 1590 kHz
In a simple series RLC circuit, from first principles, determine the conditions necessary for resonance and cite the expressions for the resonant frequency in radians/s
A resistance of 100 and a capacitance of 100 µF is connected in series to the parallel combination of a 20-0 resistor and a 15-mH inductor. The circuit is energized by a 120 Vac, variable frequency supply. Derive the formula for resonant frequency and use it to find the resonant frequency.
Identify the reason for a nonsinusoidal signal being distorted when it passes through a filter. -The distortion occurs because harmonics are removed or rejected, leaving a different waveshape. -The distortion occurs because harmonics are synchronized, leaving a different waveshape. -The distortion occurs because the signal is modulated, leaving a different waveshape. -The distortion occurs because harmonics are added in the filter, leaving a different waveshape.
Calculate the bandwidth in kHz Blank 1 and an inductor's Q Blank 2 at100MHz. It has an inductance of 6mH and a series resistance of 1.2k2.
A circuit of the series LRC has R = 4 Kohm e L = 6mH. (a) What should be the value of capacitance to produce a resonance at the frequency of 40 kHz? (b) What is the maximum current rms in the circuit when is the voltage rms of the source 150 V? (c) the impedance of the inductor and capacitor, and (d) the power dissipated in the circuit
Show the capacitors, whether it is effective at low or high frequencsies Draw low frequency small-signal-equivalent circuit. AND LOWER corner is 82Hz frequency. Design the circuit. Draw the high frequency small-signal-equivalent circuit. AND UP-CORNER İS 172Hz frequency. DESİGN THE CIRCUIT.
A resistor of resistance R=1000 2 is maintained at 17 °C and it shunted by 100 µH inductor. Determine the rms noise voltage across the inductor over a frequency bandwidth of: i) 15.9 kHz Ans: 182 x10-⁹ volt Ans: 9.22 x10-8 volt 11) 159 kHz iii) 1590 kHz Ans: 2.34 x10-6 volt
A resistance of 10 Q and a capacitance of 100 µF is connected in series to the parallel combination of a 20-2 resistor and a 15-mH inductor. The circuit is energized by a 120 Vac, variable frequency supply. Derive the formula for resonant frequency and use it to find the resonant frequency.
A parallel R-L-C circuit is fed by a constant current source of variable frequency. The circuit resonates at 100 kHz and the Q-factor measured at this frequency is 5. Find the frequencies at which the amplitude of the voltage across the circuit falls to (a) 70.7% (b) 50% of the resonant frequency amplitude.
Find DFT values of x-[6 87 4] and plot amplitude and phase spectrum. Write axis labels.