A ship weights 127 MN. On filling the ship's boats on one side with water weighing 600 KN with the mean distance of the boats from the center line of the ship being 10m, the angle of displacement of the plumb line is 2°16'. The metacentric height will be nearly (Take sin 2°16' = cos 2°16′ = 0.9992 and tan 2°16' = 0.04)

A ship weights 127 MN. On filling the ship's boats on one side with water weighing 600 KN with the mean distance of the boats from the center line of the ship being 10m, the angle of displacement of the plumb line is 2°16'. The metacentric height will be nearly (Take sin 2°16' = cos 2°16′ = 0.9992 and tan 2°16' = 0.04)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the vertical displacement at point B. Note: Use two (2) decimal places in the final answer. 15KN 6kN/m Bll 2EI El EI 2.0 m 4.0m 2.0 m VD 8.0 m O 113.50/EI 153.50/EI 0149.50/EI none of the above
Determine the vertical displacement at point B. 15 kN 6 kN/m 2EI COO El El VA 2.0 m 4.0 m 2.0 m Vo 8.0 m. O 113.50/EI O 153.50/EI O 149.50/EI none of the above
The cantilever beam shown in Fig. E4.8 has a rectangular cross-section 50 mm wide by h mm high. Find the height h if the maximum deflection is not to exceed 10 mm. Use E = 10 GPa. %3D
In the figure, what is the slope of member EM ? 3 KN 2 KN 6 KN 8 KN 6 KN 2 KN 3 KN 0.50 m J 6 @ 1 m-6m K T. XX O 1:2 O 2:1 O 2:3 О 1:3
3. What will be the variation in BMD for the diagram? [Assume | = 2m]. 10 KN B A a) Rectangular b) Trapezoidal c) Triangular d) Square
1. Determine the magnitude and direction of the resultant. substitute: F=2060, B= 465, D=72, E= 22 *300KN F+6 kN D° 12 E 200KN B+2_kN 3. in
E= 29,000 ksi 10 kips IAB = 600 in IBD = 900 in A B 8 ft 12 ft 12 ft 1. Determine the vertical displacement at A. a. 0486 inches 1 b, 0.6402 inches 4 c. 0.7215 inches ! d. 0.5085 inches I e. None of the above 2. Determine the vertical displacement at C. a. 0.1907 inches t b. 0.2142 inches t c. 0.3193 inches t d. 0.1185 inches t c. None of the above
1. From the beam shown: Determine the a/d ratio of the beam, at intervals 1.0 m. Identify if the beam is long, intermediate, short, or deep beam also, determine the value of Vc (Simplified and Detailed). WDL = 13 kN/m, WLL = 15 kN/m, fc' = 28 MPa, b = 400 mm, d = 500 mm, As = 1000 sq.mr 5.0m
1. From the figure, determine a. Rx b. Ry c. Magnitude of Resultant d. The inclination of the resultant 30 kN 15 kN 70 S0 KN 30 60 33 KN 25 kN
Determine the horizontal displacement at C(Acx) by used Castigliano method Dont calculate the EI Ang Acx 4 m + ΕΙ B 150 kN 20 kN/m C A |-1.5 m−1.5 m+ El = constant E = 200 GPa 5 m 1=500(106) mm4
Calculate the earth pressure at rest and distance at which the net at rest force acts. 3 Ya = 19 kN /m 2m 8=34 ;c=3kp Vd = 17.54KN/m3 %3D 1.5m 32":c=o Vsat 21.5kN/m 3 %3D 1らm Ø=31'; c= o rsat= 22.1kN/m3 5m.
A pipe of Aluminum alloy is subjected to a tensile force F along its longitudinal axis. The pipe has an initial length of 1.2 m, an initial thickness t=1 mm and an initial outer diameter do= 10 mm. The mechanical properties of the alloy are: Modulus of Elasticity E = 75 GPa Yield stress YS = 350 MPa If a force F=12 kN is applied to the pipe, the length of the pipe becomes L=1.2282 m. Determine the permanent length of the pipe after removing the force. do F