A simple ideal Rankine cycle which uses water as the working kPa. The boiler produces a 10 MPa superheated steam at 450°C. The isentropic efficiency of the pump and turbine are 100% and 90% respectively. Calculate, (a) the heat supplied in the boiler. (b) the work produced by the turbine. (c) the quality of steam at turbine exit (d) the thermal efficiency of this cycle.

A simple ideal Rankine cycle which uses water as the working kPa. The boiler produces a 10 MPa superheated steam at 450°C. The isentropic efficiency of the pump and turbine are 100% and 90% respectively. Calculate, (a) the heat supplied in the boiler. (b) the work produced by the turbine. (c) the quality of steam at turbine exit (d) the thermal efficiency of this cycle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A simple ideal Rankine cycle which uses water as the working fluid operates its condenser at 40 °C and its boiler at 300 °C. Calculate the work produced by the turbine, the heat supplied in the boiler, and the thermal efficiency of this cycle when the steam enters the turbine without any superheating. Wpump.in Pump 0-1 9in Boiler 13 qout Turbine Condenser Wturb,out 4
In an ideal Rankine cycle, steam is generated at 4.1 MPa and 480°C. The condenser is at 32°C. Determine the cycle thermal efficiency in %.
In a Rankine cycle, water leaves the condenser as saturated liquid with a pressure of 20 kPa. Steamleaves the boiler at 4.5 MPa and 400 C. Assume a pump isentropic efficiency of 0.8 and a turbineisentropic efficiency of 0.9. Also assume that there are no pressure losses in the boiler and condenser.(a) Show the cycle on a T-s diagram.(b) Draw the schematic of the system.(c) Determine the net power output.(d) Determine the thermal efficiency of the cycle.
A Rankine cycle using superheat and reheat applications. Steam enters the stage 1 turbine at 8 MPa and a temperature of 480°C and expands at a pressure of 0.7 MPa. The steam is then reheated to a temperature of 440°C before entering the stage 2 turbine, where the steam expands in the condenser at a pressure of 0.008 MPa. The net power generated is 100 MW. Calculate : A) the thermal efficiency of the cycle, B) the mass flow rate of the steam, C) the rate of heat transferred from the condenser to the surroundings (Qout)
In an ideal Rankine cycle, steam is at 4.1 MPa and 480°C is generated for steam power plant. The condensing temperature is at 30°C. Determine the Cycle thermal efficiency (%)
In an ideal Rankine cycle, steam is at 4.1 MPa and 480°C is generated for steam power plant. The condensing temperature is at 30°C. Determine the Cycle thermal efficiency (%). Input your final answer and Show your T - S diagram and solution Clearly. thankyou...
In a Rankine cycle, steam leaves the boiler and enters the turbine at 4 MPa and 400◦C. The condenser pressure is 10 kPa. Determine the cycle efficienc
In an ideal Rankine cycle, steam generated at 3.546 Mpa and 450°C. The condenser isat 45°C. Determine (a) the ideal pump work, (b) the cycle efficiency, (c) for an enginewith the same end state, determine the engine efficiency.(Note: Draw the schematic and T-s diagram)
3.) A steam power plant uses the ideal Reheat-Regenerative Rankine cycle where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa where some steam is extracted for feedwater heating while the rest is reheated to the same temperature. After expanding again, it enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for mass taken for feedwater heating, Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate. Neglect the condensate pump work. kg 20.01%, 2667.841715.52955.97 k, 3.74, 952.32,35.69%, 3.78 kg kWh Specific Volume Internal Energy Temp Enthalpy Prom MP Entropy Sal Sat, Sat. Liquid Sat. Sat. Liquid Evap. Vapor Liquid Uy Evap. Sat. Vapor t Р 10% Evap. Vapor Up u, hr Liquid S, h h₂ 8% 8₂ 006113 .01 1.0002 206 136 .0007 1.89 1.0001 181 255 3.77 1.0001 159 675 1.0001 142 789 0005 ,00 2375.3 2375.3 7.90 2370.0 2377.9 15.81 2364.7 2380.6 22.88 2360.0 2382.9 01 2501.3 2501.4 7.91 2496.9…
3.) A steam power plant uses the ideal Reheat-Regenerative Rankine cycle where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa where some steam is extracted for feedwater heating while the rest is reheated to the same temperature. After expanding again, it enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for mass taken for feedwater heating, Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate. Neglect the condensate pump work. kJ kj kJ kJ kJ kg 1715.88- 20.01%, 2667.84- 955.97 3.74 951.96 35.68%, 3.78. " J kg kg kg kg kWh kg "
SITUATIONAL PROBLEM NO II In a reheat cycle steam at 8.0MPA and 485degC enters the turbine and expands to 1.4MPA. At this point, the steam is withdrawn and passed through a reheater. It reenters the turbine at 1.3 MPa and 720degC. Expansion now occurs to the condenser pressure of 0.0006MPa. For the cycle and 1kg of steam determine: 4. Heat added 5. Work Turbine 6. Work Net Thermal Efficiency 7.
In an ideal Rankine cycle, steam is generated at 4.1 MPa and 480°C. The condenser is at 32°C. For an engine with the same end states, determine its thermal efficiency in %.