A simple rod acted by fluctuating axial force produced a fluctuating stresses asSigma_min=100MPA, Sigma_max = 500MPA, using mod-goodman answer Q1- Q5(Sy = 400MPA, Sut = 600MPA)%3D* The equivalent fully reversed stress is

Given details: σmin=100 MPaσmax=500 MPaSy=400 MPaSut=600 MPa

Answered: A simple rod acted by fluctuating axial…

A simple rod acted by fluctuating axial force produced a fluctuating stresses as gma_min3D100MPa, Sigma_max = 500MPA, using mod-goodman answer Q1- Q5 (Sy = 400MPA, Sut = 600MPA) %3D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.27P

See similar textbooks

Related questions

Q: A brass link (Eb=105 GPa, αb=20.9 3 10–6/°C) and a steel rod (Es= 200 GPa, αs=11.7 3 10–6/°C) have…

A: Given data

Q: Find the reading of the device for tensile testing of cement mortar in the unit KN if the cement…

A: Given : Tensile strength = 1.5 MPa Area = 2*2.3 cm^2

Q: A thin steel tire is shrunk on to a locomotive wheel of 1.2 m diameter. Find the internal diameter…

A: GIVEN DATA DIAMETER D=1.2m =1200mm HOOP STRESS =100MPa E=200KN/mm2 α=6.5*10-6/'C We have to find…

Q: A simply supported shaft is shown. A constant magnitude distributed unit load p is applied as the…

A: Given: The safety factor, n = 2 The ultimate strength, Sut = 745 MPa The yield strength, Sy = 427…

Q: S A round steel alloy bar with a diameter of 19 mm and a gauge length of 76 mm was subjected to…

A: Given data:- Original length, L=76mm Original diameter, d=19mm ⇒Original area,…

Q: Q2 :A specimen of ductile cast iron having a rectangular cross section of dimensions 4.8 mm 15.9 mm…

Q: A) Describe the following, giving their advantages and disadvantages: i) Finite Volume Analysis. ii)…

Q: A machine component is subjected to fluctuating stress that varies from 60 to 120 N/mm². The…

Q: H.W. Theories Of Failure A cylindrical shaft made of steel of yield strength ôy MPa is subjected to…

A: Given: Yield strength= δyBending moment=M KN.mPower=P KWr.p.m.=NFactor of safety=F.S.E=210…

Q: This problem illustrates that the factor of safety for a machine element depends on the particular…

A: Given data as per question Diameter of shaft =15 mm F =055 KN p =7 KN t = 32 N.m considering axial…

Q: A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of 350 MPa.…

Q: the height (in mm) of cross section from strength calculation h = ?

A: working stress = yeild stress/ factor of safety = 220/1.6 = 137.5 MPa

Q: 8. A steel tube is restrained between two rigid walls 80 cm apart. At a temperature of 34°C, the…

A: Given:T1=34°CT2=28°Cd=25 mmt=1.5 mmα=11.7*10-6 m/m.°CE=200 GPa

Q: Fermt TL gaGSkin ja-0,630/a) vo My le.ly - ly It 2 + cor28 + tin20, , tan20,- sin20+ Teo20, nsn 2…

Q: Q6. A 2.25 m long solid bar (Lo) with a 32 mm diameter is placed under tension by a load (F) of 250…

A: GIVEN DATA- F=250KN L=2.25m D=32mm E=200GPa WE HAVE TO FIND CHANGE IN LENGTH

Q: Figure Q1(b) shows three rods that were assembled together and held between rigid supports. The…

A: Given data, T1 = Initial temperature = 20 °C T2 = Final temperature = 70 °C ∆T = Change in…

Q: A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for…

A: Answer: (a) The stress ratio, the stress amplitude and the mean stress: R = -1 σa = 213 MPa σm = 0…

Q: Q5. A material is made in circular rod form of diameter 1.5 cm and 200mm long. It is fixed on the…

Q: Q3) The figure below simplified a load-elongation diagram of a tensile test for low carbon steel…

A: Solution: Yield point is the point on the stress vs strain or the load vs elongation curve where a…

Q: 2. Consider a bar of AISI 1015 cold-drawn steel. Using the distortion-energy and…

A: Principal stresses, σA=30 kpsiσB=15 kpsiYield strength for AISI 1015 cold drawn steel ,Syt=47100 psi…

Q: Prob. 2.4-5. A tension specimen (diameter = do = 13 mm, gage length = Lo = 50 mm) was used to obtain…

Q: A plate with a center hole is subjected to both of axial force (F) and bending moment (M; acting…

Q: The rectangular cross section tube shown in Figure1 is subjected to a load P = 1200 N in positive X-…

A: Given data: P = 1200 N (+x axis) F = 799 N (- y axis ) Tube…

Q: A bar of dimension 130 mm x 50 mm x 45 mm, is subjected to an axial pull of 90 kN. The measured…

Q: 2. A horizontal bar of negligible mass, hinged at A in the figure and assumed rigid, is supported by…

A: RS, RB are tensions in steel and bronze Rax and Ray are the rections at pin joint A ∆S ,∆B are…

Q: Q5.A force of 1500 KN is applicd on a stcel bar, young's modulus is 200 G Pa. Length of the bar is…

Q: A portion of the stress-strain curve for a stainless steel alloy is shown in Figure Q-6. A Q-6 350…

Q: Use the von Mises failure criterion to solve for the minimum required yield stress if a factor of…

A: GIVEN DATA- σX =100MPa σY=-78MPa τXY = 30MPa WE HAVE TO CALCULATE YIELD STRESS ACCORDING TO VON…

Q: . Consider a steel alloy having the stress-strain diagram shown in the figure below: 1. Determine…

A: (As per policy experts are allowed to answer only one question (first one), for the remaining please…

Q: 3. A leaf spring in an automobile is subjected to cyclic stresses. The average stress = 150 MPa;…

Q: A steel bar 50 mm wide, 12mm thick and 300 mm long is subjected to an axial pull of 84 kN. Find the…

A: Suppose a bar of length L and Young's Modulus E is subjected to an axial force F. Then, the bar will…

Q: Shear Stress Vs Shear Strain on Brass E 250.00 Shear Strain (y) Shear Stress () 0000'0 0.0082 0.0164…

A: following is the answer to the above problem-

Q: A ho]]ow cinu]ar co]d-ro]]ed bronze ]Gi : 6,500 ksi] tube ( 1 ) with an outside diamctc'f of 1 .75…

Q: 1.6-7 A wire of length L = 2.5 m and diameter d = 1.6 mm is stretched by tensile forces P = 600 N.…

A: We can answer up to 3 sub-parts so we will answer first 3 sub-parts. Please resubmit the question by…

Q: Strength of Materials Dr. Maad Abdullah Hussein AL-ESRAA UNIVERSITY COLLEGE 8. BRINELL TEST Material…

Q: A brittle material made of ASTM grade 30 cast iron has ultimate strength in tension of 31 kpsi and…

A: given data- Ultimate strength in tension- 31 kpsi Ultimate strength in compression- 109 kpsi σx=20…

Q: tind the stresses in the steel and aluminum rods when the temperature rises to 60 C° and the…

A: Given: The temperature rise, dT = 60 C The intensity of load = 10 kN/m

Q: Date: Q4: A rectangular filleted bar as shown in figure below is subjected AISI 1050 cold-dawa seel…

Q: A bar of dimension 130 mm x 50 mm x 45 mm, is subjected to an axial pull of 90 kN. The measured…

A: Given data dimension of bar = 130 mm x 50 mm x 45 mm Load applied (P) = 90 kN change in length =…

Q: A bar is subjected to fluctuating tensile load from 20 kN to 100 kN .The material has yield strength…

A: Given: The fluctuating tensile load in a bar,P1=20 kNP2=100 kNσyt=240 MPaσe=160 MPaFactor of safety,…

Q: A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for…

A: Answer: (a) The stress ratio, the stress amplitude and mean stress: R = -1 σa = 213 MPa σm = 0 MPa…

Q: A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for…

A: Answer: (a) Stress Ratio: -1 Amplitude Stress: 213 MPa Mean Stress: 0 MPa (b) The corresponding…

Q: A circular rod of diameter 8 mm and 300 mm long is subjected to a tensile force 20 kN. Take E =…

A: Given data:

Q: A steam boiler, 1.2 meter in diameter, generates steam at a gauge pressure of 0.7 N/mm2. Assuming…

Q: The two-segment statically indeterminate bar in Fig. has a constant cross-sectional area A = 0.8…

Q: Consider a bar of cast iron under complex loading. The bar is subjected to a bending moment of M =…

Q: 1. Concept questions in forms of multiple choices, filling blanks, and/or computations. a) According…

A: Since you have asked multiple questions in a single request, we would be answering only the first…

Q: ire Q2 (d) shows a typical aluminum stress-strain curve. A mechanical en uminum that can withstand…

Q: This problem illustrates that the factor of safety for a machine element depends on the particular…

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

A simple rod acted by fluctuating axial force produced a fluctuating stresses as
Sigma_min=100MPA, Sigma_max = 500MPA, using mod-goodman answer Q1- Q5
(Sy = 400MPA, Sut = 600MPA)
%3D
* The equivalent fully reversed stress is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
Solve the preceding problem for the following data:P = 160 kN,JV = 200 tN,L = 2 m,b = 95 mm, h = 300 mm, and d = 200 mm
Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
A solid circular bar of diameter d = 50 mm (see figure) is twisted in a testing maching until the applied torque reaches the value T = 500 N ·. At this value of torque, a strain gage oriented at 45º to the axis of the bar gives a reading e = 339 × 10-6. What is the shear modulus G of the material?
Solve the preceding problem if the cube is granite (E = 80 GPa, v = 0.25) with dimensions E = 89 mm and compressive strains E = 690 X l0-6 and = = 255 X 10-6. For part (c) of Problem 7.6-5. find the maximum value of cr when the change in volume must be limited to 0.11%. For part. find the required value of when the strain energy must be 33 J.
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
Solve the preceding problem for a plate of dimensions 100 mm × 250 mm subjected to a compressive stress of 2.5 MPa in the long direction and a tensile stress of 12.0 MPa in the short direction (see figure).