A single-phase full-wave controlled rectifier using center tap transformer is fed from a 220 V, 50 Hz ac source and it is connected a resistive load R = 20 Q. Determine (a) draw circuit diagram, (b) the output voltage and current, (c) form factor, (d) ripple factor, (e) efficiency. Consider delay angle is a = 45° and turn ratio of transformer is 5:1.

A single-phase full-wave controlled rectifier using center tap transformer is fed from a 220 V, 50 Hz ac source and it is connected a resistive load R = 20 Q. Determine (a) draw circuit diagram, (b) the output voltage and current, (c) form factor, (d) ripple factor, (e) efficiency. Consider delay angle is a = 45° and turn ratio of transformer is 5:1.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a. A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer is rectified using a half wave rectifier circuit and connected to a 47.5 2 load resistor. Draw a circuit diagram of this arrangement and the waveform at each stage.
If the turns ratio of the transformer shown in the figure above is increased, the forward bias current through the diode is: (a) increases (b) decreases (c) does not change
Single phase half wave AC-AC converter has a resistance of R = 50 ohms. Input voltage is given as 230 Vrms. Transformer conversion ratio is 1:1. If T1 thyristor is triggered at 60 degrees; a)Rms output voltage? b)Output power? c)RMS load current and average load current? d)Input power factor? e)Average and RMS thyristor current?
3. A three phase bridge rectifier is supplied by 380 Volt line voltage through a Star/delta connected transformer of which turns ratio is 1. The firing delay angle is a=30° and the load is resistive R=2.2 Ohm. Draw the circuit diagram and mark the followings on this figure : average values of output voltage, the currents and voltages of each transformer leg.
Difference between sc and oc test in transformer...
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
An ideal single-phase full wave rectifier circuit has a non-inductive resistanceload, negligible tube drops and no transformer losses. What is therectification or conversion efficiency in percent?
The primary winding to secondary winding turns ratio of a centre-tapped transformer is 5:1. The primary winding of the transformer is fed from 220V ac supply and the secondary voltage is connected to a single phase full wave rectifier which consist of two diodes. The forward resistance of each diode is 50 and load resistance is 250. Determine the following: A. peak value of current B. de load current C. rms value of load current D. de power E. ac power input to rectifier F. efficiency of rectifier
Determine the regulation of a transformer in which thepercentage resistance drop is 1% and the percentagereactance drop is 5% when the power factor 0.8 leading.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R 10 kn IN4001
1. Single phase half-wave converter has a purely resistive load of R and delay angle is a= n/2 determine: (a) Rectification efficiency (b) Form factor (c) Ripple factor.
A three phase full wave rectifier is shown below along with the peak input phase voltage Vm=169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is Vpc=280.7V and. The RMS transformer secondary current is equal to 81.72A, the output RMS voltage is equal to VRMS=280.93V and the output resistance is equal to 2.8070. The TUF would be equal to: Secondary a平a字a辛 R 太D。太D。太D. Select one: 0.875 Ob. 0.955 O C. 0.551 O d. 0.432 Compared with power transistors, thyristors have the following characteristic