A sled is given a push across a horizontal surface. The sled has a mass m, the push gives it an initial speed of 3.40 m/s, and the coefficient of kinetic friction between the sled and the surface is 0.150. (a) Use energy considerations to find the distance (in m) the sled moves before it stops. m (b) What If? Determine the stopping distance (in m) for the sled if its initial speed is doubled to 6.80 m/s. m

A sled is given a push across a horizontal surface. The sled has a mass m, the push gives it an initial speed of 3.40 m/s, and the coefficient of kinetic friction between the sled and the surface is 0.150. (a) Use energy considerations to find the distance (in m) the sled moves before it stops. m (b) What If? Determine the stopping distance (in m) for the sled if its initial speed is doubled to 6.80 m/s. m

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter7: Work And Kinetic Energy

Section: Chapter Questions

Problem 100CP: The surface of the preceding problem is modified so that the coefficient of kinetic friction is...

See similar textbooks

Similar questions

In a Coyote/Road Runner cartoon clip (https://openstaxcollege.org/l/21coyroadcarcl), a spring expands quickly and sends the coyote into a rock. If the spring extended 5 m and sent the coyote of mass 20 kg to a speed of 15 m/s, (a) what is the spring constant of this spring? (b) If the coyote were sent vertically into the air with the energy given to him by the spring, how high could he go if there were no non-conservative forces?
A person in good physical condition can put out 100 W of useful power for several hours at a stretch, perhaps by pedaling a mechanism that drives an electric generator. Neglecting any problems of generator efficiency and practical considerations such as resting time: (a) How many people ‘would it take to nm a 4.O0-kW electric clothes dryer? (b) How many people would it take to replace a large electric power plant that generates 800 MW?
An electric scooter has a battery capable of supplying 120 Wh of energy. If friction forces and other losses account for 60.0% of the energy usage, what altitude change can a rider achieve when driving in hilly ter-rain if the rider and scooter have a combined weight of 890 N?
A shopper pushes a grocery cart 20.0 m at constant speed on level ground, against a 35.0 N frictional force. He pushes in a direction 25.0° below the horizontal. (a) What is the work done on the cart by friction? (b) What is the work done on the cart by the gravitational force? (c) What is the work done on the cart by the shopper? (d) Find the force the shopper exerts, using energy considerations. (e) What is the total work done on the cart?
A 100 — kg man is skiing across level ground at a speed of 8.0 m/s when he comes to the small slope 1.8 m higher than ground level shown in the following figure. (a) If the skier coasts up the bill, what is his speed when he reaches the top plateau? Assume friction between the snow and skis is negligible. (b) What is his speed when he reaches the upper level if an 80 — N frictional force acts on the skis?
A large cruise ship of mass 6.50 107 kg has a speed of 12.0 m/s at some instant. (a) What is the ships kinetic energy at this time? (b) How much work is required to stop it? (c) What is the magnitude of the constant force required to stop it as it undergoes a displacement of 2.50 km?
Repeat the preceding problem, but this time, suppose that the work done by air resistance cannot be ignored. Let the work done by the air resistance when the skier goes from A to B along the given hilly path be —2000 J. The work done by air resistance is negative since the air resistance acts in the opposite direction to the displacement. Supposing the mass of the skier is 50 kg, what is the speed of the skier at point B ?
A block of mass m = 5.00 kg is released from point and slides on the frictionless track shown in Figure P7.6. Determine (a) the blocks speed at points and and (b) the net work done by the gravitational force on the block as it moves from point to point . Figure P7.6
The surface of the preceding problem is modified so that the coefficient of kinetic friction is decreased. The same horizontal force is applied to the crate, and after being pushed 8.0 m, its speed is 5.0 m/s. How much work is now done by the force of friction? Assume that the crate starts at rest.
A mouse of mass 200 g falls 100 m down a vertical mine shaft and lands at the bottom with a speed of 8.0 m/s. During its fall, how much work is done on the mouse by air resistance?
Check Your Understanding The spring Example 7.5 is compressed 6 cm from its equilibrium length. (a) Does the spring force do positive or negative work and (b) what is the magnitude?
A particle of mass 0.50 kg moves along the x -axis with a potential energy whose dependence on x is shown below. (a) What is the force on the particle at x = 2.0, 5.0, 8.0, and 12 m? (b) If the total mechanical energy E of the particle is —6.0 J, what are the minimum and maximum positions of the particle? (c) What are these positions if E = 2.0 J? (d) If E = 16 J, what are the speeds of the particle at the positions listed in part (a)?