A solid 1.20 in. diameter shaft is subjected to a torque of T = 230 lb-ft and an axial load of P = 6500 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i %p2 = i A Tmax in-plane = i H Save for Later (1) psi psi T BO psi (b) Show the stresses of part (a) and their directions on an appropriate sketch. eTextbook and Media Attempts: unlimited Submit Answer

A solid 1.20 in. diameter shaft is subjected to a torque of T = 230 lb-ft and an axial load of P = 6500 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i %p2 = i A Tmax in-plane = i H Save for Later (1) psi psi T BO psi (b) Show the stresses of part (a) and their directions on an appropriate sketch. eTextbook and Media Attempts: unlimited Submit Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A solid 2.20 in. diameter shaft is subjected to a torque of T = 365 lb-ft and an axial load of P = 4700 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i Op2 i = Tmax in-plane A i H (1) psi psi psi T B (b) Show the stresses of part (a) and their directions on an appropriate sketch.
7.A cast-iron machine part is acted upon by the 3kN.m couple shown. Knowing that E=165GPA and neglecting the effect of fillets. i) Determine the maximum tensile and compressive stress in the casting ii) Determine the radius of curvature of the casting. 90 mm 20 mm 40 mm 30 mm M = 3 kN m
4. A rigid block of having a weight M is suspended by symmetrically placed rods. Each copper rod has an area of 1200 sq.mm: E= 125,000 MPa and the allowable stress is 90 MPa. The steel rod has an area of 1500 sq.mm; E 220GPa; and the allowable stress is 120 Mpa. Determine the largest weight M which can be supported by the rods. 8c=8s Copper 160 mm Pc Ps Steel 240 mm TIT Pc ..initial level Tinal level Copper 160 mm
A solid 1.00 in. diameter shaft is subjected to a torque of T = 240 lb-ft and an axial load of P = 5000 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i Op2 = i Tmax in-plane A i H (1) 요. 요.. psi psi T B psi P X (b) Show the stresses of part (a) and their directions on an appropriate sketch.
The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G = 39 GPa). Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm, determine the angle of twist at A. 60 mm TB = 1600 N-m 36 mm TA = 800 N·m A 400 mm B 375 mm --- 250 mm Then, determine the maximum and minimum shearing stress in shaft CD.
The material used for the shaft has an allowable shear stress of tallow= 40 MPa. If the members are connected together with a fillet weld of radius r= 2.25 mm, determine the maximum torque T that can be applied. Where will the largest stress occur? 30 mm 30 mm 15 mm T T T Figure 6
P = 9 kip 2 in. 1 in. 1.5 ft The aluminum post shown in the figure is reinforced with a brass core. If this assembly supports an axial compressive load of P = 9 kips applied to the rigid cap, determine the average normal stress in the aluminum and the brass. Take Eal=10103ksi and Ebr= 15103ksi.
Required information A cast-iron tube is used to support a compressive load of 3 kip. Given: E= 10.5 x 10° psi and that the maximum allowable change in length is 0.025 % and the outer diameter of the tube is 1.8 in, determine, (a) Allowable inner diameter of the tube (b) Is the value a minimum/maximum? Why? The maximum stress in the member is given as Omax (ps)
The thin rectangular plate is uniformly deformed such that Ex = 220E, Ey= -680 uE, and yy = 870 urad. If a = 35 mm, determine (a) the normal strain &, in the plate. (b) the normal strain &, in the plate. (c) the shear strain ynt in the plate. B D. a a a a a a a a a Answers: (a) En= i HE (b) Et= i HE (c) Ynt = i prad
Portions of a 0.25 × 0.25-in. square bar have been bent to form the two machine components shown. Knowing that the allowable stress is 9 ksi, determine the maximum load that can be applied to each component. (a) P₁ 1.1 in. P¹ (b)
Current Attempt in Progress A solid 1.10 in. diameter shaft is subjected to a torque of T = 370 lb-ft and an axial load of P = 4200 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i op2 = i Tmax in-plane i (1) Save for Later psi psi T B psi P (b) Show the stresses of part (a) and their directions on an appropriate sketch.
Problem 1 Please choose the correct answer and also write down your solution. (1) The beam is subjected to the shown loading. What is the correct statement regarding the flexural stress at A and B? P P a. Both og and og are tensile stress. 0.5 m 0.5 m 0.5 m b. Both oa and og are compressive stress. Og is tensile stress and og is compressive stress. с. d. OA is compressive stress and og is tensile stress. A В (2) The cantilever beam is subjected to the load P and has cross section as shown. What is the ratio of the magnitudes of the maximum tensile and compressive flexural stresses over the a-a cross section? b. 3/7 a. 7/2 d. 2/10 е. 3/10 h. 10/3 c. 7/3 f. 10/2 i. 1/1 g. 2/7 250 mm 20 mm 60 mm 200 mm 2 m 1 m 15 mm 15 mm