A solid aluminum shaft of 60 mm diameter fits concentrically in a hollow steel tube. The aluminum shaft carries an axial compressive load of 240 kN. Assume v = 1/3 and ESt = 70 GPa. Which of the following most nearly gives the minimum internal diameter of the steel tube so that no contact pressure exists? Which of the following most nearly gives the transverse strain? Which of the following most nearly gives the axial compressive stress in the aluminum?

A solid aluminum shaft of 60 mm diameter fits concentrically in a hollow steel tube. The aluminum shaft carries an axial compressive load of 240 kN. Assume v = 1/3 and ESt = 70 GPa. Which of the following most nearly gives the minimum internal diameter of the steel tube so that no contact pressure exists? Which of the following most nearly gives the transverse strain? Which of the following most nearly gives the axial compressive stress in the aluminum?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.9P: The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10...

See similar textbooks

Similar questions

A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.
Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
An aluminum tube has inside diameter dx= 50 mm, shear modulus of elasticity G = 27 GPa, v = 0.33, and torque T = 4.0 kN · m. The allowable shear stress in the aluminum is 50 MPa, and the allowable normal strain is 900 X 10-6. Determine the required outside diameter d2 Re-compute the required outside diameter d2, if allowable normal stress is 62 MPa and allowable shear strain is 1.7 X 10-3.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A cube of cast iron with sides of length a = 4.0 in. (see figure) is tested in a laboratory under triaxialsire.ss. Gages mounted on the testing machine show that the compressive strains in the material arc a = -225 X l06and,ay = 37.5 X l0_. Determine the following quantities: (a) the norm al stresses i. r,.. and acting on the x, y, and z faces of the cube; (b) the maximum shear stress r in the material; (C) the change ..W in the volume of the cube: (d) the strain energy U stored in the cube; (e) the maximum value of s when the change in volume must be limited to O.O28%; and (f) the required value of when the strain energy must be 38 in.-lb. (Assume £ = 14,000 ksi and v = 0.25.)
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
The stresses acting on a stress element on the arm of a power excavator (see figure) are ax= 52 MPa and txy= 33 MPa (sec figure). What is the allowable range of values for the stress if the maximum shear stress is limited to = 37 MPa?
The normal and shear stresses acting on element A are 6500 psi, 17,300 psi, and 2900 psi (see the figure b for Problem 7.2-5). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.