A solid round steel rod with Sy = 350 MPa is 945 mm long and 62 mm in diameter. With a safety factor of 5, what axial compressive load (in kN) can be applied if both ends are built in, as shown in the figure below?

A solid round steel rod with Sy = 350 MPa is 945 mm long and 62 mm in diameter. With a safety factor of 5, what axial compressive load (in kN) can be applied if both ends are built in, as shown in the figure below?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Related questions

Q: A rectangular reinforced concrete beam with width of 300mm and effective depth of 600mm is subjected...

Q: A tank contains Carbon Tetrachloride which has a mass of 853 g and a total volume of 0.0011 m^3. Det...

Q: 3.5 A linear spring supports a body weighing 50 lb. In free vibration the body oscillates at a frequ...

Q: Material A (shown below) is experiencing forces shown below at different points along its body. If t...

Q: Using Isohyetal Method, find average rainfall over a catchment. The datas are: Isohyetes (cm) 12 13 ...

Q: What is the location of the Maximum moment from A in meters. Given: w = 14, a = 3, b = 5, and c = 2....

Q: In a constant-volume process, 202 J of energy is transferred by heat to 0.90 mol of an ideal monatom...

A: In constant volume process: Volume, V=ConstantHence, dV=0 (a) Calculating he work done on the gas W=...

Q: 180KN 25KN/m 30KN/m 15 kN/m C 3.00 meters 1.50 meters 3.00 meters

Q: What is the location of the Maximum moment from A in meters. Given: w = 17, a = 2, b = 6, and c = 2....

Q: F8-8. Determine the equation of the elastic curve for the beam using the x coordinate that is valid ...

A: Given beam

Q: 2 kip 200 lb/ft B 6 ft 9 ft 9 ft–

Q: The cable is supported at points A and B 210m horizontally apart, with B 30m higher than A. The cabl...

Q: Recent trends in use of new materials such as advanced composite materials and new testing technique...

Q: A tank in the shape of sphere is filled with fluid and then pressurized. The diameter of the tank is...

A: We will apply formula of hoop stress.

Q: 3. Compute the moment of force F=450 lb and of force P= 361 Ib about point A, B, C and D. А. P D

Q: 400 lb 400 lb 200 lb/ft -3 ft- -6 ft -3 ft-

A: Draw the shear diagram for the beam. Draw the moment diagram for the beam.

Q: Give an example of how to convert a mg/L solution extract from a soil to mol/kg solid. (show dimensi...

Q: If 300L of Carbon dioxide at 25°C and 140 kPaa is compressed isentropically to 70 L. Which nearly gi...

A: To determine gage pressure following isentropic (adiabatic) compression. Given, Initial volume (V1...

Q: Calculate the member forces of the loaded structure.

A: According to given data Calculate the member forces of the loaded structure. Given load 60 KN , 40...

Q: The results of a constant head permeability test for a fine sand are as follows: Diameter of the sam...

A: Given data of constant head permeability test Diameter of the sample (Ds) = 47 cm Length of sample...

Q: 22 The dry density of a soil is 1,795.96 kg/m3. GIven that Gs = 2.68, what would be the moisture co...

Q: Question 2(a) Analyse the beam ABCD in Figure Q2(a) for the support moments at B and C. Use the mome...

Q: is at the interface of sand and clay. The unit weight of sand is 17.98 kN/m3, saturated unit weight ...

A: Given data- Height of clay layer (h) = 8m Height of sand layer = 5m unit weight of sand = 17.98 kN/m...

Q: For a falling head permeability test, the following values are given: Length of specimen = 38.5 cm, ...

Q: 8 kips 4 kips 4 kips d, =2" 15 kips 15 kips -d2 =1.5" !0 kips 20 kips d, =3" A Fig. for Problem #2

A: There are 3 bars AB, BC, CDThe forces on those bars are also given.Diameter of bar CD, d1 = 2 inches...

Q: Gate AB in figure below is a homogenous mass of 180 kg, 1.2 meter wide into the paper, resting on sm...

A: For what water depth h in meters will the force at point B be zero?

Q: The following data were obtained by stadia observation: vertical angle Ѳ = +9degree25min, upper stad...

A: We will use formula of tacheometer

Q: The steel pipe (G - 75GPA) has an outer diameter of 50mm and an inner diameter of 30mm, It is fixed ...

A: Given:- The modulus of rigidity of the steel pipe = G = 75 GPa The outer diameter of the pipe = 50 ...

Q: 296. Compute for the torsional deflection in degrees of a 110 mm diameter, 1.4 m long shaft subjecte...

A: To determine the torsional deflection (angle of twist) for given shaft and twisting moment. Given,...

Q: 220KN/m 190KN/m A B "a" 3.00 m 3.00 m

Q: Three wood boards, each 4 in wide, are joined by the 3/4-in-diameter bolt. If the working stresses f...

Q: The data shown below are the results of a liquid limit test done on a soil. Moisture Content (%) ...

Q: A bar of a certain material has 50 mm x 50 mm cross-section. When it is subjected to an axial pull o...

Q: the horizontal bar shown (length = 15.0 feet) rests on smooth indines. compute the distance X at whi...

Q: The common tangent AB of a compound curve is 76.42 m with azimuth of 268°30' The vertex V being inac...

Q: Identify at least 2 concrete manifestation of the role that science and Technology play in nation bu...

A: science and technology helping in building the nation in various ways 1)improving the poverty 2)imp...

Q: Calculate the percent voids between aggregate particles that have been com- pacted by rodding, if th...

Q: 180KN 25KN/m 30KN/m 15 kN/m 3.00 meters 1.50 meterS 3.00 meters

Q: An equal-tangent vertical curve connects a -2.2% and a +3.2% grade. The low point of the curve is at...

A: The given data is shown below: G1=-2.2%G2=+3.2%Elevation of low point=302.3 ftElevation of PVI=300 f...

Q: The given data shows a sieve analysis of a soil sample. Classify the soil using AASHTO Method. Table...

A: following table of data from sieve analysis is given:

Q: A block of wood 0.2 m thick is floating in sea water. The specific gravity of wood is 0.65 while tha...

A: Given, Thickness of wood (t) = 0.2 m Specific gravity of wood (Gw) = 0.65 Specific gravity of sea w...

Q: Can you draw a free body diagram of this problem and given solution? so I can clearly understand. Th...

A: Force values are given in question.

Q: A cube (E = 200GPA) is experiencing stress from all directions. Along thex-direction, there is a com...

Q: The flow of traffic along North Reclamation is 1800 vehicles per hour with a space mean speed o 90 k...

A: solution Given vehicles per hour =1800 vph average mean speed v=90kph

Q: 2.5m 3.2m A Cable 1 Cable 2 B 4.0m 2.3m MN kN

Q: If the total bursting force is to be taken care of by the hoops, find tension in each hoop if water ...

A: The values given in the question are as follows Top diameter of tank(DT)=2 m Bottom diameter of tank...

Q: A and a cable DB. Find: Draw a free body diagram to determine the components of reactions. 1.5 m 1.5...

A: Free Body Diagram

Q: The rigid beam is supported by a pin support at A and steel wires BD and CE (E-20OGPA). The steel wi...

Q: 1. Determine the resultant internal loadings acting on the cross section at C of the cantilevered be...

Q: Which of the following statements is not correct in relation to building codes? A building code DOES...

A: Building codes- These are the rules, regulations, and provisions according to which any building con...

Concept explainers

Measuring site work, Excavation and Piling

Bid drawings typically include very little material about the precise requirements of site work operations, measuring site work and excavation work differs from measuring most other works on a construction project. The actual site work conditions are not provided and also the dimensions of the excavations are not known during the pre-construction phase. The precise measurement of the excavation and backfill of the earth material and topsoil is important for a contractor to decide upon the total cost required for the process. All the works should be carried out under OSHA (Occupational Safety and Health Administration) standards to ensure the safety of the workers.

Question

I need in handwritten Format. I will dislike if you submit typed answer.

A solid round steel rod with Sy = 350 MPa is 945 mm long and 62 mm in diameter. With a safety factor of 5, what axial compressive load (in kN) can be
applied if both ends are built in, as shown in the figure below?
Selected Answer:
211.335
Correct Answer:
197.120 t 1%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Measuring sitework, excavation and piling

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q # 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. The value of P is limited to 20 KN in bronze, 72 KN in aluminum and 28 KN in steel Find the area of each section that will not exceed a stress in steel of 280 MPa, in aluminum of 180 MPa, or in bronze of 200 MPa. CLO -2 Steel Aluminum Bronze 2P 4P 2.5 2.0 1.5
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN. 0.8m 0.4m B 5KN 0.6m Al 20KN Q2 5) What is the deformation 8, in mm? A=800 mm? A=1,200 mm?
A solid round steel rod with Sy = 350 MPa is 945 mm long and 62 mm in diameter. With a safety factor of 5, what axial compressive load (in kN) can be applied if both ends are built in, as shown in the figure below? Selected Answer: 211.335 Correct Answer: 197.120 t 1%
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm? A = 400mm? A - 200mm 40KN 10KN 20KN 2.5m 2.0m 1.5m
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm A = 400mm? A- 200mm 40KN 10KN 20KN 1.5m 2.5m 2.0m Determine the change in length of steel rod having a length of 800mm and a diameter of 6.5mm. The rod is subjected to a force P equal to 110KN. Young's Modulus is 200GPA Compute normal strain of the rod
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
An aluminum [E = 9100 ksi] control rod with a circular cross section must not stretch more than 0.23 in. when the tension in the rod is 2100 lb. If the maximum allowable normal stress in the rod is 10.9 ksi, determine: (a) the smallest diameter d that can be used for the rod. (b) the corresponding maximum length L of the rod. Answers: (a) d = (b) L = i i in. in.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
A flanged bolt coupling consists of six 12-mm diameter steel bolts evenly spaced around a bolt circle 300 mm in diameter, and four 25-mm diameter aluminum bolts on a concentric bolt circle 200 mm in diameter. What torque can be applied without exceeding a shearing stress of 60 MPa in the steel and 40 MPa in the aluminum? Use G of ateel = 83 GPa and G for aluminum = 28 GPa. Express your final answer in N.m to the nearest whole number. Do not include the unit in your answe
4. For the rods shown, determine (a) the compressive force after a temperature rise of 95°C, (b) the corresponding change in length of the aluminum rod. 0.5 m Aluminum A = 2.0x10-3 m2 E 70 GPa a= 23x10-6/Oc + 0.3 m Bronze A = 1.5x10-3 m2 E = 110 GPa d=18x10-6/0c .0 mm