A solid steel shaft in a rolling mill transmits 20 kW of power at 2 Hz. Determine the smallest safe diameter of the shaft if the shear stress τw is not to exceed 40 MPa and the angle of twist θ is limited to 6°in a length of 3 m. Use G = 83 GPa.

A solid steel shaft in a rolling mill transmits 20 kW of power at 2 Hz. Determine the smallest safe diameter of the shaft if the shear stress τw is not to exceed 40 MPa and the angle of twist θ is limited to 6°in a length of 3 m. Use G = 83 GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Related questions

Q: Determine the dimensions of a hollow shaft with a diameter ratio of 3:4 which is to transmit 60 kW…

A: Given information: Hollow shaft with diameter ratio 3:4That is Inside DiameterOutside Diameter =…

Q: The maximum allowable shear stress in a hollow shaft of external diameter equal to twice the…

A: Given, Maximum allowable shear stress=80MPa Torques (T)=4000Nm Bending Moment (M)=3000Nm Let inner…

Q: Q// The mean dimensions of the cross section of an airplane fuselage are shown. If the fuelage is…

A: Given data: Shear modulus (G) = 3.9×103 ksi Allowable shear stress = 18 ksi Angle of twist per unit…

Q: 3.8 Attaching a hollow shaft to a solid shaft creates the steel shaft. Determine the maximum torque…

Q: A solid steel circular shaft transmits 18 kW of power at 120 rpm. Determine the minimum diameter of…

Q: A solid shaft is required to transmit 90 kW of power at 200 rpm. Determine the shaft diameter by the…

A: The power P can be given by - P=90×1000=2πNT6090×1000= 2π×200×T60T=4297.18 NmThe shear stress can be…

Q: 14. The output shaft, with a diamater of 20 mm, from an electric motor drives a compressor on a…

Q: Calculate the shaft diameter and torsion angle since the maximum torsional moment is 150 Nm for a 1…

Q: A hollow shaft for marine applications has outer and inner diameters of 400 mm and 200 mm…

Q: (a) the maximum shear stress in the shaft; and (b) the angle of twist in degrees. Use G =12 x 106…

Q: A solid shaft transmits 1.7 kW of power at 4.4 Hz. What is the smallest safe diameter of the shaft…

A: The expression to calculate the maximum shear stress is…

Q: 10 41. The hydrofioil boat has an A-36 steel propeller shaft that is 30 m long, It is connected to…

A: Given, Length of Shaft (L) = 30 m Power (P)= 2000 kW No. of rotations of shaft = 1700 rpm Outer…

Q: A hollow shaft transmits 7 MW at 200 rev/min. It is supposed that the maximum allowable stress is…

A: Given, P=7 MW=7×106 WN=200 RPMτ=70 MN/m2=70×106 N/m2G=80 GN/m2=80×109 N/m2θL=0.40/m=0.4×π180…

Q: A steel propeller for a windmill transmits 5 kW at 87.9 rpm. If the allowable shear stress in the…

Q: A solid steel shaft A of 60 mm diameter rotates at 300 rev/min. Find the greatest power that can be…

Q: A B E F 20 kN-m 35 kN-m 85 kN-m 30 kN-n

A: given d=0.2m = 200mm so r = 100mm

Q: If T = 600 Nm, determine the absolute maximum shear stress in the shaft (in MPa) b. If the maximum…

Q: A solid circular shaft is required to carry a twisting moment of 6 x 10 N-m and a bending moment of…

Q: When subject to an applied torque,a circular shaft of length 600mm twists through an angle of 2°,if…

Q: A hollow steel shaft is stressed to 55 MPa by a torque of 135600Nm. Determine the outside diameter…

A: Given data: τ=55 MPaT=135600 N.md=23DG=83 GPa Need to determine the outside diameter.

Q: While transmitting power of a steam turbine, the angle of twist of a rotating shaft was measured and…

A: When the force is applied in tangential direction in the plane of transverse cross-section, torque…

Q: QUESTION 2: 2.1 A shaft is to transmit 190 kW at 180 rev/min. If the maximum torque transmitted is…

Q: A steel propeller for a windmill transmits 5.7 kW at 43.4 rpm. If the allowable shear stress in the…

Q: SS 304 steel shaft is 3 m long and has an outer diameter of 60 mm. When it is rotating at 60 rad/s,…

Q: The 25 mm diameter shaft is made of a material having an allowable shear stress of 80 MPa. If the…

Q: The driveshaft of an automobile is being designed to transmit 203 hp at 2940 rpm. Determine the…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 12.25 in. and…

Q: The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque…

Q: Q5: Determine the diameter of the solid shaft where the angle of twist not exceed 10 and the length…

A: Given: The angle of the twist: →θ=1°=1×π180=0.017 radian Diameter of the shaft=d And length of the…

Q: A hollow shaft for marine applications has outer and inner diameters of 400 mm and 200 mm…

Q: 3. A motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: WHILE TRANSMITTING POWER OF A STEAM TURBINE, THE ANGLE OF TWIST OF A ROTATING SHAFT WAS MEASURED AND…

A: When the force is applied in tangential direction in the plane of transverse cross-section, torque…

Q: A solid shaft with a diameter of 20 mm is shown below. The shaft is fixed at points A and B. In the…

A: As per given question question a) Draw a torque diagram for this shaft. b) Determine the maximum…

Q: tubular steel [G = 80 GPa] shaft is being designed to transmit 150 kW at 30 Hz. The maximum shear…

Q: A solid circular shaft of steel is transmitting 20 kW of power at 120 rpm. Determine the minimum…

Q: A solid circular drive shaft of length = 0.5 m, is to be designed to transmit up to 45000 W at 1800…

Q: Determine the absolute maximum shear stress in the shaft. Express your answer to three significant…

Q: solid steel shaft has a diameter of d and a length of L had used to transmit a power of 120 kW at…

Q: in Pa) using the maximum torque T that can be applied to the ends of the shaft without exceeding a…

Q: The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque…

Q: If the internal torque experienced by a solid brass shaft (G =39 GPa) with radius r=50 mm is T = 12…

A: Consider a twisting moment T is applied to a shaft having radius R. Then, torsional shear stress…

Q: Determine the diameter of a solid steel shaft which will transmit 112.5 kW at 200 rpm. Also…

A: Given data, P= 112.5 kW =112500 W N= 200 rpm. θ=1.5° =0.0261799 rad. τ=55 N/mm² =55000000 N/m²…

Q: While transmitting power of a steam turbine, the angle of twist of a rotating shaft was measured and…

A: When the force is applied in tangential direction in the plane of transverse cross-section, torque…

Q: A hollow circular shaft is required to transmit 300 metric horsepower at 200 r.p.m. The maximum…

A: Given data

Q: A solid 1.500-in.-diameter steel shaft is subjected to torques TB = 290 lb-ft and TD= 125 lb-ft,…

A: Given data: ◆ The diameter of solid shaft: d = 1.500 in ◆ The torque applied at gear D: TD = 125…

Q: Problem 2

Q: shaft is subjected to an axial pull of 22N and transverse sheer force of 12KN The yield strength of…

A: Given: Axial load (P)=22N (Check the value is N or KN again)Transverse shear force (F)=12kNYield…

Q: A 3-meter solid steel shaft, with an unknown diameter, twists by 5° as it experienced a shear stress…

A: GIVEN DATA- L=3m Angle of twist =5' Shear stress =60MPa G=83GPa

Q: 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the .9 The compound…

A: Answer: The angle of rotation of the free end is 16.3°.

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A solid shaft (100 mm diameter) transmits 75 kW at 150 rpm. Determine the value of maximum shear stress set up in the shaft and the angle of twist per metre of the shaft length if G=80 GN/m².
3. The transmission shaft shown receives power at gear A and transmits them to gear B and gear C. Determine the maximum stress in the shaft. Determine the total angle of twist. Use G = 70 GPa. 3kW @ 1000 rpm 2 kW 1 kW A 200 mm 200 mm Ø 25 mm Ø 20 mm
A solid shaft in a rolling mill transmits 30 hp at 100 rpm. Find the diameter in mm of the shaft so as not to exceed a shearing stress of 42 MPa and an angle of twist of more than 5 degrees in a length of 3 meters. G = 83 GPa
A solid circular shaft of steel is transmitting 20 kW of power at 120 rpm. Determine the minimum diameter of the shaft if the angle of twist is limited to 5.5° in a length of 3.5 meters and the shear stress is not to exceed 45 MPa. Use G = 83 x 10° Pa.
A solid shaft in a rolling mill transmits 20 kW at 2 Hz. Determine the diameter of the shaft if the shearing stress isnot to exceed 40 MPa and the angle of twist is limited to 6° in a length of 3m. Use G = 83 GPa. Note: Round the diameter value to the safest 5-mm multiple.
A solid shaft 2 m. long is stressed 60 MPa when transmitted a power of 50 kW at 2 rev / sec. If G = 83 GN / m2, determine the diameter of the shaft (mm.), and the angle of twist in the shaft.
Design the smallest diameter of the solid shaft if its rotation is to produce 600 HP at 15 revolutions per second. The maximum shear stress of the material is limited to 65 MPa when twisted through maximum of 5 degrees. Use G = 28 GPa. The length of the shaft is 5 meters
The tubular drive shaft for the propeller of a hovercraft is 6 m long. If the motor delivers 4 MW of power to the shaft when the propellers rotate at 25 rad>s, determine the required inner diameter of the shaft if the outer diameter is 250 mm. What is the angle of twist of the shaft when it is operating? Take tallow = 90 MPa and G = 75 GPa.
Determine the diameter of a solid steel shaft which will transmit 112.5 kW at 200 rpm. Also determine the length of the shaft if the twist must not exceed 1.5o over the entire length. The maximum shear stress is limited to 55 N/mm2. Take the value of modulus of rigidity = 8 x 104 N/mm2.
A steel core is bonded firmly to the copper tube (shell) to form the shaft shown. The length of the shaft is 450 mm and the end A is fixed to the wall. Take the shear modulus of steel and copper as 76 GPa and 38 GPa, respectively. The diameter of the core is 60 mm and the outer diameter of the shaft is 100 mm. Determine the maximum external torque (Tmax) so that the absolute maximum shear stress for any point H on the surface of the copper shell does not exceed 50 MPa. 450 mm A 100 mm 60 mm В Tmax =? kN · m
The wrench is applied to two forces each of magnitude P. The steel shaft AB has a diameter of 15 mm. If the shear stress in the shaft is not exceed 120 MPa and the angle of twist is not exceed 5; find the largest allowable of P. For steel; use G = 80 GPa.