A steel bar, with a rectangular cross section, has a butt-welded joint, as shown below, and will be used to carry an axial tensile load of 750 kN. If the normal and shear stresses on the plane of the weld must be limited to 80 MPa and 50 MPa, respectively, determine the minimum thickness t required for the bar.

A steel bar, with a rectangular cross section, has a butt-welded joint, as shown below, and will be used to carry an axial tensile load of 750 kN. If the normal and shear stresses on the plane of the weld must be limited to 80 MPa and 50 MPa, respectively, determine the minimum thickness t required for the bar.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 60 mm long and 6 mm thick fillet weld carries a steady load of 15 kN along the weld. The shear strength of the weld material is equal to 200 MPa. The factor of safety is (a) 2.4 (c) 4.8 (b) 3.4 (d) 6.8
Problem 3.1: Determine the design strength of a 1 mm length of a 6.35 mm fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength Fexx = 483 MPa. Assume that the load is to be applied parallel to the weld length. Problem 3.2: Repeat problem 3.1 if the weld is 500 mm long. Problem 3.3: Repeat problem 3.1 if the weld is 750 mm long. Problem 3.4: Repeat problem 3.2 if the application of the load is at an angle of 35 degrees from the longitudinal axis of the weld. Problem 3.5: Repeat problem 3.3 if the application of the load is at an angle of 35 degrees from the longitudinal axis of the weld.
Determine the length of the fillet weld lap joint shown in the figure below. The weld has to resist a tension of 115 kips. The effective throat for the weld h = 0.5 inches, and the allowable stress is 21 ksi. length → F = 115 kips h
4) A welded connection, as shown in Fig. 2, is subjected to an eccentric force of 60 kN in the plane of the welds. Determine the size of the welds, if the permissible shear stress for the weld is 200 N/mm2. 60 kN 100 W2 -150 50 Fig. 2 Assume static conditions. 10.09 mm 20.09 mm 30.09 mm 40.09 mm
1. The welded joint shown below is subjected to a 40 kN of static axial and a 40 kN of static bending loads (F and F1) as shown below. The materials are made of steel with Sut-2070 MPa and Sy=1830MPA. Calculate the factor of safety of the weld. Where, h-6 mm, b-30 mm, c=100 mm d-60 mm, and both forces are equal and each 40 kN (F=F1=40 kN). F F1 d State the reason of your selection in your answer but use only 2 sentences (maximum of 2 lines!) for each answer. 2) Suggest the most suitable bearing type with quantity if a shaft rotates at a speed of 1500 rev/min, subjected to mid-range radial load in a limited radial space. 3) Suggest the most suitable bearing type with quantity if maximum stiffness, stability and resistance to shaft misalignment are desired at a shaft, rotating at 1000 rev/min, under a light radial load. In addition, the shaft is subjected to comparably light thrust loads from either directions. 4) Suggest the most suitable spring type for the following application…
3.) The diagram below shows a 5.5m long double angle brace which is connected by 6mm welding connection. The length of weld shown in the picture is 300 mm on the top and 100 mm on the bottom. The 2-L127x 89x6.4 are 300W steel and long leg back-to-back. The braces are to be welded to a 12 mm 350W steel gusset plate. Determine the factored tensile capacity of the angles. Any intermediate connections that are required should also be specified. 740 kN -12 mm Gusset Plate
A plate 100 mm wide and 12.5 mm thick is to be welded to another plate by means of parallel fillet welds. The plates are subjected to a load of 50 kN. Find the length of the weld so that the maximum stress does not exceed 56 MPa. Consider the joint first under static loading and then under fatigue loading.
Situation 2: The lap splice shown will develop a full strength as shown in the figure. Using E70 electrodes. The width of the plate is 150 mm and the thickness is 10 mm. Use Fy = 248 MPa T4 46 mm 48 mm 1. Which of the following nearly gives the diameter of the slot weld using the LRFD method. O 45 mm T O 47 mm T W
1. A butt weld is set on the cross section of an I-shaped beam. There are bending moment M and shear force V at the splicing position, where M=1120 kN•m and V= 374 kN. The beam is made of Q355b steel and semi-automatic weld is used with welding rod E50. The design value of the weld tensile strength f," is 260 N/mm². Please check whether the strength of the butt weld is safe by calculation. 280 M M 0001
An AISI 1050 HR solid tube of 20mm diameter is acted by force F1 = IkN, and force F2 of 2kN. The tube is welded to a larger round base by 3mm fillet weldment, the base is connected to the ground base (shown in gray color) by means of four bolts M8x1.25mm (property class of 4.8)). The bolts are evenly distributed at 20mm away from the center of the tube. R=100 F1 120 120. F2 R=100 D =20 120 R=3 D =60 40 Dimensions are in mm Perform the following the following: 1- Find the state of stress for the most critical point on the assembly and build the mohr's circle. Solve question 1
Two aluminum plates, each having a width b = 7.5” and thickness t = 2”, are welded together as shown in the figure. Assume that a = 5.0”. Specifications require that the normal and shear stress magnitudes acting in the weld material may not exceed 40 ksi and 25 ksi, respectively. The largest axial load P that can be applied to the aluminum plates is _____ kips.
Q1: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a thickness h and is of AISI 1040 steel. The vertical support is likewise AISI 1040 HR steel. The electrode is given in the table below. Estimate the static load F the bar can carry if two fillet welds are used. b (mm) d (mm) h (mm) Elecrode E8010 30 70 6 ko →→ F