A steel (G = 12,000 ksi) shaft is bolted with end flanges to wall supports at A and C. The pipe has an outer diameter of 2.875" and a wall thickness of 0.203". The eight holes in the flange at A were drilled slightly larger than required such that flange A can rotate slightly (0.5°) before the bolts engage. The eight holes at C were drilled to the correct size. An 80 in-kip torque is applied at B. Determine the maximum shear stress in sections (1) and (2). (1) 10 ft. 15 ft

A steel (G = 12,000 ksi) shaft is bolted with end flanges to wall supports at A and C. The pipe has an outer diameter of 2.875" and a wall thickness of 0.203". The eight holes in the flange at A were drilled slightly larger than required such that flange A can rotate slightly (0.5°) before the bolts engage. The eight holes at C were drilled to the correct size. An 80 in-kip torque is applied at B. Determine the maximum shear stress in sections (1) and (2). (1) 10 ft. 15 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please solve, include the diagrams, and do not copy from other bartleby answers. Handwritten solution is more preferred than typed. A 40-mm diameter, 522-mm length shaft is drilled, for a part of its length L1, to a 20 mm diameter and for the remaining length L2 to a 30 mm diameter drill hole. If the allowable shear stress is 86 MPa, find the maximum power that the shaft can transmit at a speed of 226 rev/min. If the angle of twist in the length of 20 mm diameter drill hole is equal to that in the 30 mm diameter drill hole, find the length of the shaft that has been drilled to 20 mm and 30 mm diameter.
Q2: A rectangular key is used to connect a gear on a shaft of d=50 mm. The shaft transmitting power at a maximum shear stress. The shaft is made of AISI 1040 CD steel and the key is made of AISI 1020 CD steel. Design the dimensions of the key. Take F.S =3.
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 400 The shaft is mounted on two 400 400 270 250 210 640i ]640 100
The shaft shown in the figure below and rotating at a speed of 1 radian / sec transmits 9 kW of power from the gear at the B point to the pulley at the D point. Manufactured from cold drawn AISI 1040 steel, the shaft is machined to the given dimensions and bedded from A and C points. The highest working temperature of the spindle is 50 ° C. At point D; Since (d2 / d3 = 1.1) and (r /d = 0.1), determine the diameter d3 of the shaft using Goodman's theory. (kb = kc = kf = 1, q = 0.8 and qs = 0.9) 200 mm 140 mm 60 mm F1= 5F Fa Kasnak 160 Ry F2 = F Dig!! Ray Ray
The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. G=83 GPa for steel -20KW JOKN -20kw -30kW 2m 1.5m 1.5m B (a) If a uniform shaft diameter of 125 mm B speci fied, detenmine the angle of rotation of A relative to D. O f segment Co is to be replaced lay a hollaw Shaft with an inside diameter of 80 mm, what is the outside diameter if the stress is not to excced 70 MPa.
A shaft is designed to transmit power of 100 kW at 180 rpm. The allowable shear stress is 50MPa and modulus of rigidity of 80 GPa. The angle of twist is not to exceed to 1° in 4-meter length A. Calculate the diameter of the shaft in inches. B.If the shaft in A is to be fitted to a hub with material SAE 0105 and fit classification of FN3, what will be the maximum and minimum stresses based on the interference of metal.
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 400 The shaft is mounted on two 400 400 270 250 ]640 210 640 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 100
Solve the problem. A 11-in. connecting rod in an engine connects the wrist pin of a piston at point A to the end of a second rod at point on the crankshaft. As the piston moves forward and back, the crankshaft is turned counterclockwise around point C. The stroke length of the engine is the distance that the piston travels (one way) with its cylinder. If the stroke length is 4 in., and the engine turns at 600 rpm, write a model representing the distance d (in inches) from A to the center of the crankshaft Cas a function of time t (in minutes). Assume that at t = 0, the piston is at its farthest point from the crankshaft. B B C C B A A stroke length
Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. 35 in A Y bearing bearing gear c: radius 2.0 in 2 in-k gear b: shaft ab: shaft ce: radius 5.0 in b a radius 0.5 in 5 in-k radius = 0.7 in d. bearing e bearing all shafts: G = 12000 ksi 25 in 30 in
Problem 2: F = 10 kip -10 in- -5 in- -5 in- d/5 R. R1 d/ 10 R. 1.4 d- R2 I in The shaft shown above rotates at 1200 RPM and supports a 10 kip load. The material of the shaft is 1095 hot-rolled steel and its surface is machined and then polished. Using a factor of safety of 1.6, specify the minimum value of diameter d for a life of 1,000 hours.
A motor driving a solid circular steel shaft transmits 85 horsepower to a gear at point B (see sketch below). The allowable shear stress in the steel shaft is 6000 pounds per square inch. Determine: The minimum diameter d of the shaft if the shaft is operated at 1350 rpm (revolutions per minute). If the shaft transmits the same power (85 horsepower) at 3500 rpm, will the shaft diameter be larger or smaller than the required diameter of part 1.
Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 55 MPa in the shafts and 23 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.