A Step aown converter is feeding an inductive load with R-10 Ohms, Le15 mH and E15V. The supply is vs-200V, the switching frequency is 10 kHz and the duty cycle is k-0.5. The maximum peak to peak ripple current in the load is equal to 0.34A. The erage load current la would be equal to: Select one: O a. 8.SA O b. 18A OC11A O d. None of these

A Step aown converter is feeding an inductive load with R-10 Ohms, Le15 mH and E15V. The supply is vs-200V, the switching frequency is 10 kHz and the duty cycle is k-0.5. The maximum peak to peak ripple current in the load is equal to 0.34A. The erage load current la would be equal to: Select one: O a. 8.SA O b. 18A OC11A O d. None of these

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

A step up chopper has input voltage 110 V and output voltage 150 V. The value of duty cycle is.
An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?
Question 4 A boost converter has an input of 5V and an output of 20W at 15V. The minimum inductor current must be no less than 50% of the average. The output voltage ripple must be less than 1%. The switching frequency is 30kHz. Determine the duty ratio, minimum inductor value, and minimum capacitor value. Verify your answers using Matlab, show the inductor current is continues and its minimum is no less than 50% of its average. Furthermore, the output voltage ripple is less than 1%.
A step down converter is operated with a duty cycle of k 0.75. The input voltage is V, 20V. and the load is L=5mH, R=152 The minimum inductor current is I 0.1A. The maximum inductor current is %3D %3D Select one: O a. 0.9 A O b. 1.9 A O C. None of these O d. 1.1 A O e.2A
Q6) The waveform of the voltage obtained after rectification is of a -----nature and therefore contains .harmonics a. Sinusoidal O b. Triangular c. Pulsating O d. Repetitive O
An R-L load is connected to a 250 V, 400 Hz step down dc converter. The average load current is 100 A. The load resistance is 0.5 Ohm. The allowed ripple limit is 15%. The minimum value of inductor to limit the maximum ripple current is:
The three phase converter with an ac side inductance L2 25 uh and VLL equal to
What is the importance of the charecteristic curve in PN Junction
I need answer with explaination In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
the following waveform is the inductor current of the buck converter, the ripple current is equal to Q7) the following waveform is the inductor current of the buck converter, the ripple current is equal to Inductor current 35 30- 25- 20- Lead voltage Oa) 14A b) 15A c) 16A d) 17A
A Capacitor filter is used at the output across the load to minimize the ripple factor of the output voltage. If R = 20 02 and the single- phase bridge rectifier is supplied from a 120V - 60 Hz sinusoidal source. Find the capacitor value in millifarads that will maintain the amount of the output ripples to less than 5% 艹 Ce = m₂ 0 mF RL%
A step up converter is operated with a duty cycle of k = 0.75. The input voltage is V, = 20V. and the load is: L= 5mH, R = 202. The minimum source current is I = 10A The maximum inductor current is %3D Select one: O a. None of these O b. 24 A Oc 12 A O d. 22 A O e. 16 A