A stream of air at 35.0°C and a gauge pressure of 0.400 atm (Stream 1) flows into a pipe passing through a heater, emerges at 77.0°C and 0.200 atm (gauge), and splits into two streams. Stream 2 passes out of the system, and Stream 3 goes through another heater and emerges at 160.0°C and 0.050 atm (gauge). Flowmeters mounted in streams 1 and 2 show readings of 3120 L/min and 1940 L/min respectively. What should the flowmeter for Stream 3 read after the stream emerges from the heater?

A stream of air at 35.0°C and a gauge pressure of 0.400 atm (Stream 1) flows into a pipe passing through a heater, emerges at 77.0°C and 0.200 atm (gauge), and splits into two streams. Stream 2 passes out of the system, and Stream 3 goes through another heater and emerges at 160.0°C and 0.050 atm (gauge). Flowmeters mounted in streams 1 and 2 show readings of 3120 L/min and 1940 L/min respectively. What should the flowmeter for Stream 3 read after the stream emerges from the heater?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The flow of water in a horizontal pipe of constant cross section has a pressure gauge at location 1 with a pressure of 100psig and a pressure gauge at location 2 with a pressure of 75psig. Using the principle of energy equation, what is the headloss between the two pressure gauges?
3. A pump steadily circulates oil used for lubricating heavy machine tools. The volume flow rate and temperature of the oil are 300 gal/min and 104°F, respectively. At 104°F, the kinematic viscosity and the specific gravity of the oil are 2.15 x 10-3 ft² /s and 0.89, respectively. The pipe lengths are 25 ft for the 4-in diameter pipe and 75 ft for the 3-in diameter one. The Schedule-40 steel pipe has an average roughness element size of 0.0018 in. If all minor losses can be ignored, evaluate how much power (in a unit of horsepower) the pump delivers to the oil. 6 ft 22 ft Flow 15 ft Discharge line 3-in Schedule 40 Suction line 4-in Schedule 40 steel pipe steel pipe Pump
Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.Water flows through a schedule-40 pipe that changes gradually in diameter from 6 in (154mm) at point A to 18 in (429 mm) at point B. The volumetric flow rate is 5.0 *3/sec (130 L/s). The respecLve pressures at points A and B are 10 psia (70 kPa) and 7 psia (48.3 kPa). All lossesare insignificant. What are the direcLon of flow and velocity at point A? (A) 3.2 */sec (1 m/s); from A to B(B) 25 */sec (7.0 m/s); from A to B(C) 3.2 */sec (1 m/s); from B to A(D) 25 */sec (7.5 m/s); from A to B
On a single plot, plot three curves that show the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below. Delta P on y axis and flow rate on the x axis. The pressure range is 0 to 1 MPa. (Branches 1 and 3 are in the same plane; branch 2 is located 5 m above the other two branches. Pipe inner diameter: 0.0254 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
) where AP is the static The Hagen-Poiseuille equation for the laminar flow through a circular pipe is: AP pressure drop measured over some length of pipe, L. Use the Hagen-Poiseuille equation and the Darcy-Weisbach equation to derive an expression for the fanning friction factor, f, for laminar flow through a circular pipe where Re is the Reynolds number. Choose one answer from the list below: of= of O None of the above 32 Re 16 Re O f = 64 Re = o f = 32μLc 3 d² 8 Re O f = 16 Re
As a process engineer, you are designing a new drinking water treatment plant using conventional treatment process including Two Rapid Mixers as follows: The design flow is 50 million gallons per day (MGD) (1 Gallon = 3.785 L, 1 m³ = 1000 L). The average temperature of water is 5°C with a dynamic viscosity, μ = 1.519 x 10-3 Pa.Sec In each rapid mixer with a square shape, detention time, e = 1 min, water depth H = 13 ft, and power input P = 1.5 kw (1 ft = 0.3048 m, 1 KW = 1,000 W) The equivalent diameter, TE for each rapid mixer is ________ m. TE || AIR 1) 4.1 2) 4.4 3) 4.6 4) 4.8 5) 0.4
Q 2. Air at 400°C and 1.7 bar flows through a horizontal 8.2-cm ID pipe at a velocity of 50.0 m/s. I. Calculate Ék (W)? Assuming ideal gas behavior and Mol.Wt (Air)=29 g/mol. I. If the air is cooled to 250°C at constant pressure, what is AER? III. Why would it be incorrect to say that the rate of transfer of heat to the gas must equal the rate of change of kinetic energy?
A fluid is being pumped through a pipe. The density of fluid is 872 kg/m³. The viscosity is 2.8x102 Pa.s. The velocity in the pipe is 5.9 m/s. If the Reynolds number is 2100. a- What is the pipe cross-sectional area? b- If the pipe cross-sectional area increased 1.5 fold under same Reynold number, density and viscosity, what is the new velocity?
A pitot-static probe is used to determine the flow velocity of air at 20°C by using water manometer as shown in Figure 5. If the vertical difference of both arms in the manometer is 6 cm. Find, i. pitot formula to obtain the flow velocity ii. the pressure difference inside the system, and iii. air velocity inside the system. Air Pitot 6 cm tube Manometer Figure 5
Consider the setup shown below, with a valve to adjust the flow of a fluid to an orifice meter equipped with a differential manometer across it, in series with a rotameter that has been previously calibrated for liquid acetone (density= 0.791 g/cm3), the fluid of interest. The rotameter calibration expression was found to be V=1.56R, where the volumetric flow rate is in mL/s and the rotameter reading is unitless. The manometer fluid has a specific gravity of 1.210. a) For one valve setting resulting in a rotameter reading of 82.0 as liquid acetone flows through the system, the height difference of the manometer fluid is 22.0 mm. The volumetric flow rate for this condition in mL/s with 3 sig. fig's is b) For one valve setting resulting in a rotameter reading of 80.0 as liquid acetone flows through the system, the height difference of the manometer fluid is 22.3 mm. The pressure drop for this condition in Pascals (Pa) with 3 sig. fig's is
1. A pressure gauge attached to a pipe is reading 1.34 m of Hg at a place where the atmospheric pressure is 10.33 m of water. The approximate absolute pressure at the mountain isa. 930 kPab. 181 kPac. 280 kPad. 100 kPa 2. The flow is said to be unsteady and non-uniform when,a. The flow velocity is not changing with time but changing with spaceb. The flow velocity is changing with both time and spacec. The flow velocity is changing with time but not changing with spaced. The flow velocity is not changing with both time and space 3. The below figure shows a pipe with a circular cross section of diameter D mm on the left end and a square cross section with side D mm on the right end. Mercury enters the left end with a velocity 1 cm/s and leaves the right end with a velocity V2. Find V2 (neglect losses in the pipe).a. Cannot be find since length is not givenb. Cannot be find since diameter is not givenc. 7.85 mm/sd. 12.73 mm/s 4. 1 kg water is flowing through an inclined pipe at…
Q3/ A petroleum crude oil having a kinematics viscosity 0.0001 m²/s is flowing through the piping arrangement shown in the below Figure,The total mass flow rate is equal 10 kg/s entering in pipe (A) . The flow divides to three pipes ( B, C, D). The steel pipes are schedule 40 pipe. note that the dynamic viscosity 0.088 kg/m.s. Calculate the following using SI units: 1- The type of flow in pipe (A). 2- The mass velocity in pipe (B) GB. 3- The velocity in pipe (D) Up. 4- The Volumetric flow rate in pipe (D) QD. 5- The Volumetric flow rate in pipe (C) Qc. Oe = 2 o mm UB = 2UA Perralenm crude oL mic =? -> ma = 1o Kg/s = 50 mm Go 7000 K/m.s %3D Note that!. = 30 mm D: 0iameter, UIvelocity G mass velocity mass How ate.