A tank, well insulated, has two parts divided by partition. The first part incuded 3,5 kg of water at 800 kPa while the other part is evacuated. This partition is removed and the water expands to fill the entire tank. If the final pressure and temperature are 100 kPa and 200°C, respectively, please determine a- The volume of the tank b- Temperature of the water for first part

A tank, well insulated, has two parts divided by partition. The first part incuded 3,5 kg of water at 800 kPa while the other part is evacuated. This partition is removed and the water expands to fill the entire tank. If the final pressure and temperature are 100 kPa and 200°C, respectively, please determine a- The volume of the tank b- Temperature of the water for first part

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter37: Air Distribution And Balance

Section: Chapter Questions

Problem 2RQ: The two ways that fresh air enters a structure are _______and_____.

See similar textbooks

Similar questions

A sealed rigid vessel has a volume of 35 ft and contains 2 Ibm of water at 200 F. The vessel is now heated. If safety pressure valve is installed at what pressure should the valve be set to have a maximum temperature of 400 F?
Skg of Steam at pressure of 4.9 bar is produ- ced from water at 20c. Determine the amount of heat supplied if the Steam is o.9 dy.
Question # 3 - Water of 2 kg fills a part of the chamber with P = 300 kPa. The other part of the chamber is separated by a partition from the water part, and it is empty and evacuated. The total chamber volume is 1.5 m³; the part filled with water has 1/3 of the total volume. If the partition between the two parts is removed and water expands inside the entire chamber, determine the following: a) The water temperature before removing the partition b) The pressure after removing the partition if T = 3 °C c) For part (b), find the specific enthalpy water
the specific heat capacity of the system during a certain process is given by Cn(0.4+0.004T) kJ/kg deg. celcius. if the mass of the gas is 6kg and its temperature changes from 25 def. celcius to 125 def. celcius find the mean specific heat of the gas
Question 1 A piston-cylinder assembly with a frictionless piston has a volume of 0.1 m' and initially filled with steam of 0.5 kg at a pressure of 0.4 MPa. There is heat transfer until the temperature reaches 573 K. Find the total heat transfer as well as the work done during the process. Sketch the process on a P-v diagram with respect to the vapour dome.
A closed rigid tank has a capacity of 2.5 m3. It holds air at 400 kPa and 18 deg C. Heat is added until the temperature is 350 degC. Determine the heat added in kJ. Given a vacuum pressure of 165 mmHg. The barometric pressure is 745 mmHg. Find the absolute pressure in kPa. What is the amount of dry steam flow to an engine, which is supplied with 4500 kg per hour wet steam with a quality of 80%?
A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 400 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.5 mkg. Water Heat Figure Qlb i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work đuring the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
(b) A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 300 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.7 m'/kg. Water Heat Figure Qlb i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work during the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
The rigid sealed vessel with a safety pressure valve, as shown, has a volume 0.8 m and contains 0.6 kg of water at 110 C, the vessel is now heated. At what pressure should the safety valve be set to have maximum temperature of 240 C in the vessel. safty valve Steam or vapor Liquid
6. What is the temperature of the heated air at 170°C in K, °F and R?
Determine the average constant pressure specific heatof gas if 522 kJ/kg of heat is necessary to raise the temperature from 300 ̊K to 800 ̊K making the pressure constant. Ans. 1.004 kJ/kgoK
Argon in the amount of 1.5 kg fills a 0.04-m3 pistoncylinder device at 550 kPa. The piston is now moved by changing the weights until the volume is twice its original size. During this process, argon's temperature is maintained constant. Determine the final pressure in the device in psi. Select one: O a. 550 O b. 40 O c. 80 O d. 275