A tensile bar has an initial 2.000-in. gauge length and a circular cross-sectional area of 0.2 in.?. The loads and corresponding gauge lengths recorded in a tensile test are show below. After fracture the bar diameter was 0.370 in. Load Gauge length (in.) (Ib) 2.0000 6,000 12,000 15,000 18,000 21,000 24,000 25,000 2.0017 2.0034 2.0042 2.0088 2.043 2.30 2.55 22.000 В.00

A tensile bar has an initial 2.000-in. gauge length and a circular cross-sectional area of 0.2 in.?. The loads and corresponding gauge lengths recorded in a tensile test are show below. After fracture the bar diameter was 0.370 in. Load Gauge length (in.) (Ib) 2.0000 6,000 12,000 15,000 18,000 21,000 24,000 25,000 2.0017 2.0034 2.0042 2.0088 2.043 2.30 2.55 22.000 В.00

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Q1- The followving data was obtained tensile test on a specimen of 6 mm diameter and gauge length Lo=30 mm: 92.7 160.4 155 4.06 142 124.7 5.1 5.84 0| 38 load(KN) elongation(mm) 0 0.02 Using the graphic paper supplied, Plot engineering stress-strain curves, then determine the 76.2 107 149 0.12 0.25 0.50 2.03 3.55 (gy sy), (gu, cu), (of, sf), modulus of elasticity, then detected in the draw ((strain hardening (n)), (Necking), (uniform plastic region and non-uniform plastic region) and (elastic & plastic) region))?
A tensile bar has an initial 2.000-in. gauge length and a circular cross-sectional area of 0.2 in.?. The loads and corresponding gauge lengths recorded in a tensile test are show below. After fracture the bar diameter was 0.370 in. Gauge length (in.) Load (Ib) 2.0000 6,000 12,000 15,000 18,000 21,000 24,000 25,000 22,000 2.0017 2.0034 2.0042 2.0088 2.043 2.30 2.55 B.00 а) b) c) Plot the data as engineering stress versus engineering strain. Compute the modulus of elasticity. Determine the yield strength at a strain offset of 0.002.
4. Sample of steel bar has 50 mm length after performing tension test the final length was 50.2 mm, strain of this sample equal to * 0.04% 0.4% 4% 0.004% O All above are not correct
The rectangular plate undergoes a deformation shown by the dashed lines where D= 5.7 in., dj = 0.1 in. , and d2 = 0.18 in. (Figure 1) Part A Determine the shear strain yry at point A Express your answer to three significant figures and include appropriate units. HA Value Units Submit Request Answer Figure 1 of 1 Part B Determine the shear strain Yr'y' at point A. Express your answer to three significant figures and include appropriate units. d, ? di- D Value Units
Method of Consistent DeformationThe encircled numbers are 2 square inch, 2 square inch, 1 square inch respectively
A hole is to be punched through a steel plate of 8 mm thickness. What is the least diameter of hole which can be punched, if the steel punch can be worked to a compressive stress of 800 N/mm² and the ultimate shear strength is 300 N/mm²? A 1.2 mm B 12 mm C 21 mm D 2.1 mm
Given: E= 29x10^6 psi A= 2in^2 Determine the deformations members AB, BC, BE, DE and DF. Please show your complete handwritten solution.
Class work I diameter Given: metal specimen x-section (circular) = 0.55 in. Gage length = 2.030 fm. in. Fracture occurred at pounds # final length final dia. Determine 28,500 € = 2.30 in. = 0.43 in. tensile stress in kşi c) Reduction of x-sect, area a percentage pricentage as a a) Ultimate 6) Elongation as Note: Gaye length - length over which elongation is measured all
Define the terms shear stress and shear strain, illustrating your answer by meansof a simple sketch. Two circular bars, one of brass and the other of steel, are to beloaded by a shear load of 30 kN. Determine the necessary diameter of the bars (a) insingle shear, (b) in double shear, if the shear stress in the two materials must notexceed 50 MN/m2and 100 MN/m2respectively.
Two strips of plastic material are bonded together using splice plates as shown. The average shearing stress in the glue must be limited to 1,050 kPa. If P = 45 kN, what splice plate length L is required? a. 142.9 mm b. 149.2 mm c. 192.4 mm d. 124.9 mm