A thin beam of mass m and length L has a particle of mass 2m attached at one end. The particle has negligible radius. The beam rotates around point O and and is initially at rest in the hori- zontal position shown. Determine the angular velocity w at the instant the beam passes through the vertical position after being released. (Hint: Find the inertia of the entire system around point O by using the parallel axis theorem. Use the work-energy principle.) (1/4)L m (3/4)L 2m

A thin beam of mass m and length L has a particle of mass 2m attached at one end. The particle has negligible radius. The beam rotates around point O and and is initially at rest in the hori- zontal position shown. Determine the angular velocity w at the instant the beam passes through the vertical position after being released. (Hint: Find the inertia of the entire system around point O by using the parallel axis theorem. Use the work-energy principle.) (1/4)L m (3/4)L 2m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3.32). As shown in Figure 3, a yo-yo toy is formed by wrapping a massless cord around adisk of radius R= 0.2 m and mass M=3 kg. The cord is vertical and its top end is fixed and the disk isinitially stationary. The cord remains vertical for the entire motion and does not slide on the disk.When the disk is released from rest, it falls down by a distance H=0.8 m, The moment of inertia ofthe disk around its center is I disk=1/2mdiskR^2a . Find the angular acceleration of the disk when it is lowered by a distance H.b . Find the angular velocity of the disk when it is lowered by a distance H.
A 256-lb block is released from rest when the spring is unstretched. The drum has a weight of 76 lb and a radius of gyration of kO = 0.9 ft about its center of mass O. The coefficient of stiffness of the spring is k=78 lb/ft. The radius of the drum are: rin=0.485ft and rout=0.82ft. Find the velocity of the block after it has descended d=4 feet.
In the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)
bucket of mass m is hanging from the free end of a rope whose other end is wrapped around a drum (radius R, mass M) that can rotate with negligible friction about a stationary horizontal axis. The drum is not a uniform cylinder and has unknown moment of inertia. When you release the bucket from rest, you find that it has a downward acceleration of magnitude a. What are (a) the tension in the cable between the drum and the bucket and (b) the moment of inertia of the drum about its rotation axis?
A uniform rod (mass = 1.8 kg) is 1.5 m long. The rod is pivoted about a horizontal, frictionless pin through one end. The rod is released from rest in a horizontal position. What is the angular speed of the rod (in rad/s) when the rod makes an angle of 23° with the horizontal?. The moment of inertia of the rod about this axis is given by (1/3)ML2.
The slotted circular disk whose mass is 4.9 kg has a radius of gyration about O of 230 mm. The disk carries the four steel balls, each of mass 0.17 kg and located as shown, and rotates freely about a vertical axis through O with an angular speed of 164 rev/min. Each of the small balls is held in place by a latching device not shown. If the balls are released while the disk is rotating and come to rest relative to the disk at the outer ends of the slots, compute the new angular speed N of the disk. Also find the magnitude |ΔE| of the energy loss due to the impact of the balls with the ends of the slots. Neglect the diameter of the balls and discuss this approximation.
The connecting rod of a horizontal reciprocating engine is 400 mm and length of the stroke is 200mm. The mass of the reciprocating parts is 125 kg and that the connecting rod is 100 kg. The radius of gyration of the connecting rod about an axis through the centre of gravity is 120 mm and the distance of centre of gravity of the connecting rod from big end centre is 160 mm. The engine runs at750 r.p.m. Determine graphically the torque exerted on the crankshaft when the crank has turned 30° from the inner dead centre.
The uniform slender rod AB of weight 5 lb and length 30 in. forms an angle β = 30° with the vertical as it strikes the smooth corner shown with a vertical velocity v1 of magnitude 8 ft/s and no angular velocity. Assuming that the impact is perfectly plastic, determine the angular velocity of the rod immediately after the impact.
A rigid body is made of three identical thin rods, each of mass m and length L= 0.6 m,attached together in the form of an H. The body is allowed to fall from the horizontalposition, rotating around one of the legs of the H.a) What is the rotational inertia of the H, in terms of m and L?b) What will be the angular speed of the H when it is oriented vertically?
The mass of gear A is 25 kg and its centroidal radius of gyration is 105 mm. The mass of gear B is 13 kg and its centroidal radius of gyration is 85 mm. Calculate the angular acceleration of gear B when a torque of 16 N·m is applied to the shaft of gear A. Neglect friction. The angular acceleration is positive if counterclockwise, negative if clockwise..
A, B, C and D are four masses carried by a rotating shaft at radii 100 mm, 156mm, 152 mm and 200 mm respectively. The planes in which the masses rotateare spaced at 500 mm apart. The magnitude of the masses B, C and D are 9 kg, 5 kg and4 kg respectively. Find the required mass A and the relative angular settings of the fourmasses so that the shaft shall be in complete balance.
The gear train shown operates in a horizontal plane and is used to transmit motion to the rack D of mass mD = 4.9 kg. If an input torque M = 63 N●m is applied to gear A, what will be the magnitude of the resulting acceleration a of the unloaded rack? (The mechanism which it normally drives has been disengaged.) Gear C is keyed to the same shaft as gear B. Gears A, B, and C have pitch diameters dA = 185 mm, dB = 355 mm, and dC = 185 mm, and centroidal mass moments of inertia IA = 0.45 kg●m2, IB = 3.38 kg●m2, and IC = 0.45 kg●m2, respectively. All friction is negligible.