A vertical plate is submerged in water and has the indicated shape. 6 ft5 ft5 ft7 ft An isosceles triangle is submerged in water pointed down. The base of 6 ft is horizontal and 7 ft below the surface of the water. The other two sides are each 5 ft. Express the hydrostatic force (in ft) against one side of the plate as an integral (let the positive direction be downwards) and evaluate it. (Recall that the weight density of water is 62.5 lb/ft3.) A vertical plate is submerged in water and has the indicated shape. 6 ft 7 ft 5 ft 5 ft Express the hydrostatic force (in ft) against one side of the plate as an integral (let the positive direction be downwards) and evaluate it. (Recall that the weight density of water is 62.5 lb/ft³.) δ 1) dx = lb

A vertical plate is submerged in water and has the indicated shape. 6 ft5 ft5 ft7 ft An isosceles triangle is submerged in water pointed down. The base of 6 ft is horizontal and 7 ft below the surface of the water. The other two sides are each 5 ft. Express the hydrostatic force (in ft) against one side of the plate as an integral (let the positive direction be downwards) and evaluate it. (Recall that the weight density of water is 62.5 lb/ft3.) A vertical plate is submerged in water and has the indicated shape. 6 ft 7 ft 5 ft 5 ft Express the hydrostatic force (in ft) against one side of the plate as an integral (let the positive direction be downwards) and evaluate it. (Recall that the weight density of water is 62.5 lb/ft³.) δ 1) dx = lb

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
A triangular plate of height h=1.20 m and a base b=2.0 m is submerged vertically in water with its base at the liquid surface and parallel to it.a. Evaluate the total force acting on one side of the plate, in kN. b. Obtain the location of the force from the center of gravity of the plate, in mm.c. Obtain the location of the force from the liquid surface, in mm.
Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
Compute the value of EIy at 2.5 m from the left support.
A rectangular plate 0f 7 ft by 3.5 ft at an angle 450 with the horizontal, and the 7 ft side is horizontal. Calculate the magnitude of the force on one side of the plate and the depth of its centre of its pressure when the top of edge is (a) at free water surface(b) 1.75 ft below the water surface.
c. Slope at L/3. d. Deflection at L/3
Block A supports a pipe column and rests as shown on wedge B. Knowing that the coefficient of static friction at all surfaces of contact is 0.25 and that θ = 45degrees, determine the smallest force P required to raise block A.
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
Determine the vertical displacement at Joint A, B, C, D, E
The 600-Ib, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force P at its center. A. Determine the magnitude if the hydrostatic force acting on the gate using the hydrostatic panel equations. Express your answer in kips.
The rectangular gate has dimensions: h=.8m; b=2.4m;c=0.4m;weighs 2 tons. It slides on a plane of inclination θ=70° and serves to plug the conduit of a dam. Considering that the coefficient of friction is 0.35. Determine the magnitude of the tension T needed to move the gate when the water level reaches the elevation of 62 m.
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=30° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm² and A=50 cm² will be taken for all bars.)