A W10x30, 3.2 m long, A36 steel is used as a column with fixed ends to support a service dead load of 255 kN. Calculate the maximum service live load the column can sustain using LRFD. Use theoretical value of k. Write your answer rounded to the nearest whole number in kN. 0-5703 mm²

A W10x30, 3.2 m long, A36 steel is used as a column with fixed ends to support a service dead load of 255 kN. Calculate the maximum service live load the column can sustain using LRFD. Use theoretical value of k. Write your answer rounded to the nearest whole number in kN. 0-5703 mm²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before the load is applied. If the load P = 50 kN, determine its vertical movement. STEEL L=3 M A= 300 mm² E= 200 GPa 2m зм P= 50 KN ALUMINUM L=43 A== 1500 mm² E-7067.
Question 16 A W10x30, 2.9 m long, A36 steel is used as a column with fixed ends to support a service dead load of 154 kN. Calculate the maximum service live load the column can sustain using LRFD. Use theoretical value of k. Write your answer rounded to the nearest whole number in kN. A = 5,703 mm2 rx = 111.25 mm ry = 34.80 mm
In figure shown below B 960 Imm 640 N 3 280 mm 960 N a. Determine the tension in segment AC b. Determine the tensibn in segment BC
in (Eigure 1), w 4 kN/m and 27 kN/m. Replace. the distributed loading by an equivalent resultant force and couple moment acting at point A. Figure -3m 3m 1 of 1 Determine the equivalent resultant force. Express your answer to three significant figures and include the appropriate units. Enter positive value if the force is upward and negative value if the force is downward. Fu = Submit Part B HÅ Templates -37 Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining Submit (MR) Value KN Determine the couple moment. Express your answer to three significant figures and include the appropriate units. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise. HÅ Request Answer Pearson ? Review Units
Question 28 An A36 angle bar is used as a tension member connected on both legs with 18 mm. Given that s = 74 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile yielding in the gross area. Write your answer to the nearest whole number. |40 50 L6x 3½x% 56 62.5 Ag = 1,852 mm2 t = 8 mm
Q2\ A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. A (mm') E (GPa) Ow (MPa) =TTT Aluminum Bronze 450 83 120 3P Bronze Steel 2P P AP- Aluminum 600 70 80 Steel -0.6 m→l- - 1.0 m- H-08 m- 300 200 140
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. E=200 GPa A=D300mm? L=3m 2m 2 m 3m 1.5m Match each tem to a choice
a. Calculate "P" in KN considering tension failure on gross area Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
Y Suppose that P = 250 lb. (Figure 1) Figure T T301-381-38- W 481 46 Part C FBC = Part D Submit Request Answer FBD= Part E FCD= Submit Part F FCE= Submit Determine the force in member of the truss. Express your answer in pounds to three significant figures. Enter negative value in the case of compres the case of tension. Part G FDE= Part H - ΑΣΦ It vec Determine the force in member BD of the truss. Express your answer in pounds to three significant figures. Enter negative value in the case of compressi the case of tension. FDF= 17 ΑΣΦ Submit Part I 1 of 1 > Request Answer Submit Request Answer FEF= ΓΙ ΑΣΦ 11 Eved Submit - Η ΑΣΦΙ Request Answer Determine the force in member CD of the truss.. Express your answer in pounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension. -- ΑΣΦ Ivec Request Answer 17 ΑΣΦ 4 Part A 5 Request Answer it vec Determine the force in member AB of the truss Express your answer in pounds to…
5. The column shown in the figure is reinforced with 8 28mm diam steel with fy = 414Mpa and f'c = 21Mpa (IS 456:2000) a. What is the nominal balanced load and balanced eccentricity? b. Fing pn if e = 220mm c. Find pn if e = 550mm d. Find pn when the stress in tension steel is 180Mpa 60 mm 550 mm 60 mm 650 mm e Pn
A W16X31 A992 steel is used as a beam. The beam has a continuous lateral support. The uniformly distributed load shown in the figure is a service load that consists of 50% dead load (included the beam weight) and 50% live load. Using LRFD, determine the following? Note: A992 STEEL Fy = 50 ksi Ag = 9.13 in^2 Zx = 54.0 in^3 What is the Ultimate (Governing Load Combo) Maximum Positive and Negative Moment (at midspan) in kips-ft
Consider the Fink truss shown in (Eigure 1). Suppose that Fi=600 lb and Fy=900 lb. Figure 1 of 1 K60 60% -100- Determine the force in the member GF of the truss and state if the member is in tension or compression. Express your answer using three significant figures. Enter negative value in the case of compression and positive value in the case of tension. VAZ vec For= lb Submit Request Answer • Part B Determine the force in the member FB of the truss and state if the member is in tension or compression. Express your answer using three significant figures. Enter negative value in the case of compression and positive value in the case of tension. VAX Ivec Fre lb Previous Answers Request Answer Submit