A wood beam carries the loading shown in the figure. Calculate the magnitude of the bending stress (in Pa) at the top of the of the beam on a section 2.05 m from A if P = 4467 N, W = 1887 N/m, a = 1.12 m, b = 2.46 m, c = 1,27 m, L = 79 mm and h = 228 mm. Round off the final answer to two decimal places.

A wood beam carries the loading shown in the figure. Calculate the magnitude of the bending stress (in Pa) at the top of the of the beam on a section 2.05 m from A if P = 4467 N, W = 1887 N/m, a = 1.12 m, b = 2.46 m, c = 1,27 m, L = 79 mm and h = 228 mm. Round off the final answer to two decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SHOW COMPLETE SOLUTION AND ANSWER IN 3 DECIMAL PLACES The piece of wood ,100mm by 100mm in cross section, contains a glued joint inclined at the angle Ø with the vertical. The working stresses are 20 MPa for wood in tension . 8 MPa for glue in tension and 12 MPa for glue in shear . If Ø =50 , Determine the largest allowable axial force P.
The timber member has a cross-sectional area of 1653 mm2 and its modulus of elasticity is 12.9 GPa. Compute the change in the total length (in mm) of the member after the loads shown are applied if x = 1.67, y = 3.87, and z = 3.65. Round off the final answer in two decimal places. 40 kN 35 kN 20.8 D A B•
strength of materials... answer only A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) at a point 34 mm from the top of the of the beam on a section 1.66 m from A if P = 5381 N, W = 2349 N/m, a = 1.31 m, b = 2.12 m, c = 1.27 m, L = 72 mm and h = 239 mm. Round off the final answer to two decimal places.
A horizontal 50 kN load is applied on a 610UB125 Beam as shown in Figure 4. Determine the stresses at four corners A, B, C and D. Also, determine the angle that the neutral axis forms with the horizontal plane. The sectional properties are given in Table 1. 50k! 306 50 KN Table 2. Figure 4 (unit in mm) 306 mm bf d Y, A tr tw Section mm² mm mm mm mm 610UB125 16000 229 612 19.6 11.9 Sx lyo Sy (x106 (x10³ (x106 (x10³ mm²) mm³) mm²) mm³) 986 3680 39.3 536
UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials The assembly shown is made up of T-shape steel and two wood as shown. A bending moment M is applied to the composite beam. Given: Es = 200 GPa Ew = 25 GPa M = 90 kN.M h = 200 mm c. Calculate the absolute maximum stress in the steel in MPa. d. Calculate the stress in the steel along the top edge in MPa.
The lower ends of the 3 bars in the figure are at the same level before the rigid homogenous 18Mg block is attached. Each steel bar has an area of 566mm^2 and E=200Gpa. For the bronze barn the area is 866mm^2 and E=83Gpa. Find the stresses developed in each bar.
A wood beam carries the loading shown in the figure. calculate the maximum bending stress (in Pa) if P = 4791 N, W = 1060 N/m, a = 1.37 m, b = 2.25 m, c = 1.18 m, L = 77 mm and h = 262 mm. Round off the final answer to two decimal places. W P +²+ A B b -c→ C I [₁ h
Problem 6: The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The properties of the segments and the working stresses are listed in the table. Bronze A (in.²) Steel 2 ft E (psi) Ow (psi) Aluminum 4 ft 3 ft 2P Steel 0.75 30 × 106 20 000 Bronze 1.00 12 x 106 18 000 ЗР 4P Aluminum 0.50 10 × 106 12 000 Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 in. and the working stresses are not to be exceeded.
Therectangular wood beam is loaded asshown in the figure. Solve thefollowing:What is the maximum bendingstress in the beam?What is the maximum shear stress in the beam?
A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) at a point 49 mm from the top of the of the beam on a section 2.85 m from A if P = 5406 N, W = 2320 N/m, a = 1.08 m, b = 2.04 m, c = 1.5 m, L = 70 mm and h = 246 mm. Round off the final answer to two decimal places. W P 커다 A B b -c→| с h
The rectangular wood beam is loaded as shown in the figure. What is the maximum bending stress in the beam? * 12 kN. 8 kN/m 150 mm A C 250 mm B 1.0 m 2 m O 10.24 MPa O 5.68 MPa O 15.57 MPa O 0.80 MPa
A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) at a point 14 mm from the top of the beam on a section 3.4 m from A if P = 4619 N, W = 1991 N/m, a = 0.82 m, b = 1.77 m, c = 1.13 m, L = 68 mm and h = 197 mm. Round off the final answer to two decimal places. ... W P aptation 16 h A C t b ➜