A wood beam with a cross section 4 x 6 in. is simply supported at A and B. 4 in. ( -4 in.- Section 1-1 The beam has a length of 9 ft and is subjected to point load P = 3.7 kips at mid-span. Calculate the state of stress at point C located 4 in. below the top of the beam and 4.5 ft to the right of support A. Neglect the weight of the beam. (Enter the normal and shear stresses in ksi. For the normal stresses, use the deformation sign convention. For the shear stress, use the sign convention for shear stresses. Consider only the in-plane stresses. Assume that the +x-axis is to the right along the length of the beam and the +y-axis is up along the page.) ksi ksi ay = ksi 4.5 ft 6 in.

A wood beam with a cross section 4 x 6 in. is simply supported at A and B. 4 in. ( -4 in.- Section 1-1 The beam has a length of 9 ft and is subjected to point load P = 3.7 kips at mid-span. Calculate the state of stress at point C located 4 in. below the top of the beam and 4.5 ft to the right of support A. Neglect the weight of the beam. (Enter the normal and shear stresses in ksi. For the normal stresses, use the deformation sign convention. For the shear stress, use the sign convention for shear stresses. Consider only the in-plane stresses. Assume that the +x-axis is to the right along the length of the beam and the +y-axis is up along the page.) ksi ksi ay = ksi 4.5 ft 6 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 380mmx520mm beam is reinforced with 5 diameter 28mm steel bars (one layer). Strength of concrete is 30MPa and steel yield strength is 400MPa. Take the steel cover to be 60mm. Determine the balanced moment, kN-m Determine the maximum moment if strain in steel is 0.005 Determine the design strength of the beam, kN-m
2 A simply supported beam has a dimension of 300mmw x 600mmh has a span of 6m. it has a superimposed load of 30KN/m and live load of 50KN. It has a specified concrete strength of 28MPa and yield strength of 420MPa. Distance of centroid steel area to outermost fiber is 60mm. a. What is the maximum moment of the beam? b. What is the required tension steel area? Use et = 0.004
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-up section made from a T-Section and a Channel (C-Section) fastened together by 16mmØ bolts, equally spaced from the center of the section, with shearing capacity t=100 MPa, for bearing os = 220 MPa for rivets in single shear and os = 280 MPa for rivets in double shear. E=200GPA for all materials. 8 KN 15 KN/m 12 KN/m 2m 3m 3m 2m Properties of T-Section Br = 180 mm Tf= 16 mm Tw = 12 mm D = 210 mm Properties of C-Section B = 105 mm T = 12 mm Tw = 12 mm D = 210 mm
The beam is loaded as shown. Determine the dimension of the square beam if the maximum flexural strength at point B is 50 MPa. Show all necessary solution.
b) This is a concrete frame (the interior lines represent reinforcing bars), If P is dead load, draw the BMD and the SFD as a result of ULTIMATE LOAD. 6.0 ft. P= 1.0 Kip Own weight of the beam = 1.0 kip/ft. (Uniform dead load)
Determine the axial stress in member BE of the loaded truss if it has a circular cross-section with a diameter of 20 mm.
Given the truss and loading shown below, determine the stress at member DF if Pµ = 18.375 Kips and its area is 16 in². Assume that the truss are simply supported at joint M and E. Express your answer in ksi. Use three decimal places. RM Pu Pu 0 Pu Pu 8 @ 10' = 80' Pu B Pu CF Pu et LK J I H G F 8@10' 80' RE
A single span member is 3m in length is made up of Apitong 200mm x 300mm wooden section, with an allowable stress based on 80% stress grade. The beam carries a uniform load of 18 kN/m including its own weight. The beam carries an axial tensile load of 180 kN a.) Give the actual tensile stress if only tensile force is acting. b.) Give the interaction value of both bending and tensile stress. Determine whether the wooden section is safe or not. not redesign the wooden section. c.) Give the ratio of the difference between its actual bending and tensile stress to the adjusted bending stress for slenderness
A. Beams Analysis - Determining Moment Capacity for beam (Under-Reinforced, Over-Reinforced, Balanced Conditions) 3 #19 -350 mm- 520 mm 600 mm 80 mm *For the problem above, use f'c = 28MPa and Fy = 414MPa. C. What is the depth of the compression block "a"? d. What is the stress in the steel fs? How about the stress in f's?
*4-76. The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T = 50°F, determine the average normal stress in each member when T, = 120°F. Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in?. %3D B C. - 3 ft 2 ft
Determine the flexural capacity of the given section of beam below. b=300 d=400 d'=70 fc'=20.7 fy=415 As=4-28mm As'=2-28mm A.USE NSCP 2001, Mu = kN-m B. USE NSCP 2015, Mu kN-m
Consider the loads of the figure to be axially applied at sections B, C, and D to the concrete structure supported at A. IW E F P G 5 kN 5 kN A Determine P in kN when member BC is 24 mm in diameter, the axial stress in section F is 588 MPa, and W 309822 N. = 10 kN C 10 kN Rigid -bearing plates