A4-AWSTC crystalline silicon PV aray is operated with an appropriately sized inberter. The inverter tracks maximum power, and the array is operating at 50°C with 900 W/m2 incident on the array. There is a 2% power loss in the wiring and the inverter is 94% efficient On a typical PV system, the inverter output power will be closest to: O 3316 W O 2985 W O 2612 W 1492 V

A4-AWSTC crystalline silicon PV aray is operated with an appropriately sized inberter. The inverter tracks maximum power, and the array is operating at 50°C with 900 W/m2 incident on the array. There is a 2% power loss in the wiring and the inverter is 94% efficient On a typical PV system, the inverter output power will be closest to: O 3316 W O 2985 W O 2612 W 1492 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2. A) Draw circuit diagram and output voltage waveform of three phase inverter (120- degree condition) has Y-connected resistive load B) What are the main differences between VSI and CSI the multiple choice list for each question
In a single phase VSI bridge Inverter, the load current is Io =200 sin(wt-45°)mA. The d.c. supply voltage is 220 V. What is the power drawn from the supply ?
3. A single-phase to single-phase cycloconverter "bridge type" with input voltage and frequency 150V and 50Hz. respectively. The output frequency is 10Hz and the firing angle equal to 45°. The load is resistance with the value of 1002 in series with reactive inductance of the value of 20mH. Assume the extinction angle equal 180°. a. Draw the waveforms output voltage, output current, source current, the thyristors currents (iT, IT, IT and in) b. Calculate the rms of output voltage. c. The rms current of each thyristor. d. The input power factor
Q2 (a) Figure Q2(a) shows a single-phase full-bridge square-wave voltage source inverter has resistor (R) and inductor (L) load of 10 Q and 5 mH respectively connected in series. The inverter output frequency is 50 Hz. The transistor switching scheme is complementary bipolar. (i) Draw the output voltage and current waveforms. (ii) Obtain an expression of the rms output voltage at the fundamental frequency. (iii) If the fundamental AC output voltage is 220 V, find the required DC input voltage for the inverter. (iv) Find the instantaneos load current by considering until the 9th harmonics number. (v) Calculate the total harmonics distortion (THD) of the load current. Use only the first three odd harmonics. (vi) Sketch the harmonics spectrum for output current. (vii) Show the displacement angle a, if 5th harmonic is to be eliminated.
14 Which of the following is true? O Most often, the PFC circuit is a combination of diode rectifier circuit and single-phase inverter. O Most often, the PFC circuit is a combination of diode rectifier circuit and boost converter. O Most often, the PFC circuit is a combination of diode rectifier circuit and full-bridge DC-DC converter. Most often, the PFC circuit is a combination of thyristor rectifier circuit and DC-DC converter.
Question 2 a) Briefly explain the de chopper, inverter, controlled rectifier and ac voltage controller. b) A buck-boost regulator as shown in Figure 2 has an input voltage, Vs = 12 V. The duty cycle, k = 0.35 and the switching frequency is 30 kHz. It also has an inductance, L = 200 µH, filter capacitance, C = 440 µF. The average load current, Ia 1.25 A. Determine the: i. average output voltage, Va, ii. peak-to-peak output ripple voltage, AVc, iii. peak-to-peak output ripple current of inductor, AI, iv. peak current of the transistor, Ip, V. critical values of L and C, and vi. critical values of L and C if Vs is increased to 14 V. Estimate the change in percentage for the critical values of L and C. is Vs C Load Vo, Vs VC i, Ia Figure 2
A HVDC link is operating with 175 KV AC line voltage at the rectifier. When the DC current is 1100 Amps, the rectifier delay angle is 100 and inverter extinction angle is 200. The resistance of the line is 23 ohms and the commutating reactances of the rectifier and inverter are 22 ohms and 21 ohms. Calculate the DC voltages at the rectifier and inverter terminals and the AC line voltage at the inverter.
Two same size PV Modules are connected in Parallel. The specification of each module is given as, Number of cells = 36, Area of each cell is 12 cm x 12 cm. Assume the necessary data. Refer to the above PV Panel choose the correct statement. a. The output current of each PV Module is 2.15A b. The output current of each PV Module is 8.6A c. The output current of each PV Module is 4.3A d. The output current of each PV Module is 1.25A
Suppose line voltage may be as low as 105 Vrms or as high as 125 Vrms in a half- wave rectifier. With a 5;1 step-down transformer, the minimum peak load voltage is closest to O 29.7 V O 35.4 V O 25 V LEGO 21 V
inverter is use to convert ac to do rectifiers is use to boost the voltage Select the correct response: O True O False
2. A full wave rectifier is used to convert 400 Hz ac todc Design a full-wave rectifier power supply that will deliver a dc outpuvoltages 15V and the load current is 1A. RSIT
(i) Draw the circuit diagram of the single phase full wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation. (ii) A single phase fully controlled bridge rectifier circuit has DC output voltage 165 V for an AC supply voltage of 230 V rms. Find the firing angle delay of the circuit for the following cases (a) Converter mode (b) Inverter mode Converter mode delay angle Inverter mode delay angle