Air at 25°C flows at 50 × 10-6 kg/s within 100-mm-long channels used to cool a high thermal conductivity metal mold. Assume theflow is hydrodynamically and thermally fully developed.Air, Tmi = 25°CMold, T=50°C-Case ACase B(a) Determine the rate of heat transferred, in W, to the air for a circular channel (D =(case A).10 mm) when the mold temperature is 50°C(b) Consider air flowing under the same conditions as in case A, except now the channel is segmented into six smaller triangularsections. The flow area of case A is equal to the total flow area of case B. Determine the rate of heat transferred, in W, to the air for thesegmented channel.(c) Determine the pressure drops for cases A and B, both in Pa.

The image you sent is a solved example from a heat transfer textbook that considers fluid flow and…

Answered: Air at 25°C flows at 50 × 10-6 kg/s…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.18P

See similar textbooks

Similar questions

Water at a flow rate of 0.215 kg/s is cooled from 70°C to 30°C by passing it through a thin-walled tube of diameter of 50 mm and maintaining a coolant at 15°C in cross flow over the tube. What is the required tube length if the coolant is air and its velocity is V = 20 m/s?Water : cp = 4181 J/kg⋅K, μ = 548 × 10-6 N⋅s/m2, k = 0.643 W/m⋅K, Pr = 3.56.Air : ν = 15.89 × 10-6 m2/s, k = 0.0263 W/m⋅K, Pr = 0.707.(Hint: For external flow use Churchill/Bernstein correlation.)
Estimate the mass-transfer coefficient for moist air flowing normal to a 25 mm diameter tube (Nu = 0.615 Re0.47). The air velocity is 0.5 m/s. Assume standard air.
What is the ratio of total convective heat transfer rate to laminar convective heat transfer rate for the flow over 2 m length flat plate if 10 m/s air velocity is observed? For air: ν = 20x10-6 m2/s
Air at 1 atm with a velocity of 4 m/s and a temperature of 50oC flows over a flat plate that is at a uniform temperature of 100oC. The plate has a length of 0.20 m and a width of 0.1 m. a) What is the average heat transfer coefficient? b) What is the heat transfer rate from plate to the air? c)What is the average friction coefficient and the drag force ? d)What is the heat transfer coefficient at x=0.15 m ?
Steel (AISI 1010) plates of thickness δ = 8 mm and length L = 1.3 m on a side are conveyed from a heat treatment process and are concurrently cooled by atmospheric air of velocity u∞ = 11 m/s and T∞ = 23°C in parallel flow over the plates. For an initial plate temperature of Ti = 329°C, what is the rate of heat transfer from the plate? What is the corresponding rate of change of the plate temperature? The velocity of the air is much larger than that of the plate.
Air at atmospheric pressure and 25oC is heated in a tube with an ID of 25 mm. The tube wall is maintained at a temperature of 200oC. What length of tube is required to achieve an outlet air temperature of 120oC if the air flow is 10 Nm3/hr?
In an Osborne Reynolds Demonstration experiment, why is it the in laminar flow, the color collected has a color unlike in transitional and turbulent flow where the color of liquid is just transparent?

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning