-Determine the Reynold's number-Determine the Nusselt number-Determine the heat transfer coefficient -Estimate the heat transfer per unit length Air (at T = 300 K) flows at 1m/s normal to a 77 C, 30mm-diameter pipe and 250mm long.The following are the air properties evaluated at the film temperature:V= 1.824 x 10-5 m²/s,= 0.0281 W/mK, andkPT = 0.702

Answered: Image /qna-images/answer/7ea69563-6623-4a88-8187-85a2e2f174bd.jpg

Air (at T = 300 K) flows at 1m/s normal to a 77 C, 30mm-diameter pipe and 250mm long. The following are the air properties evaluated at the film temperature: 1.824 x 10-5 m²/s, k = 0.0281 W/mK, and PT = 0.702

Air (at T = 300 K) flows at 1m/s normal to a 77 C, 30mm-diameter pipe and 250mm long. The following are the air properties evaluated at the film temperature: 1.824 x 10-5 m²/s, k = 0.0281 W/mK, and PT = 0.702

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20 °C to 60 °C. The heating is achieved by condensing steam on the surface of the tube and subsequently the surface temperature of the tube is maintained at 90degC. Water properties are as follows: density=995kg/m3, kinematic viscosity=.657x10-6 m2/s, Pr=4.43, k=.628W/mK, cp=4178J/kgK. a) Determine the Reynolds number b) What is the thermal coefficient on question number c) what is the heat absorbed by the water?
Air with a 1.7 atm gauge and a temperature of 15°C enters a horizontal 0.075m steel pipe 70 m long. The velocity at the pipe's entry is 60 m/s. What is the pressure at the discharge end of the line assuming isothermal flow?
Water with density and kinematic viscosity of 1000 kg/m?, 1 x10-s m²/s respectively flow through a 0.1 m diameter 10 m long horizontal pipe and Figure 1 shows the exponent value (n) for power laws velocity profiles. If average velocity of the flow is 1 m/s, determine; (i) (ii) centerline velocity; and time average velocity at a location of 0.025 m from the pipe centerline. 11 10 6 10 10 10 Re= ND Figure 1: the exponent value (n) for power laws velocity profiles
A 20 °C water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40 °C The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.86 W/m deg C, Re=3840000, and Pr=0.7)?
Cooling water for a power plant is stored in a pond 900 m in length and 400 m wide. A dry wind at 300 K blows in a horizontal direction parallel to the 900 m side of the pond at a velocity of 2 m/s. The cooling water is at 300 K. Known the air dynamic viscosity v= 1.67 x10m?/s.; the Re transition from laminar flow to turbulent flow is 500,000; and the saturated water vapor pressure at 300 K is 3580 Pa; gas constant R= 8.3144 J/mole.K. 1.) At what position across the pond is the air flow no longer laminar? Would it reasonable to assume that the mean gas-film mass transfer coefficient for water vapor in air is dominated by turbulent flow mass transfer? 2.) As part of an engineering analysis to predict the evaporation rate of water from the pond, determine the mean gas film mass transfer co-efficient. 3.) Calculate the rate of water evaporation from the pond.
Water flows at a rate of 0.1 kg/s in a tube with a diameter of 250 mm. The tube is heated uniformly at a rate of 135 kW/m2. Find the wall temperature at a location where Tsat = 180 C and x = 25%. [Ans.: Ts = 188 C]
Air flows inside a tube 60 mm in diameter (d) and 2.1 m long (l) at a velocity w = 5 m/sec. Find the heat-transfer coefficient α if the mean air temperature tf = 100oC. Note: Write your answer in space provided without the unit (the answer is in kcal/m2-hr-oC, one decimal places)
. Oil enters a 1.25-cm diameter,3-m long tube at 38°C. The tube wall is maintained at 66°C, and flow velocity is 0.3 m/s. What is the total heat transfer to the oil and oil exit temperature? Assume an exit temperature of 50°C. Temperature (°C) p(kg/m³) u (kg/m sec) Cp J/hg °C) k(W/m °C) 0.210 0.0725 0.0320 40 0.144 867.05 864.04 1964 60 2047 0.140 80 852.02 2131 0.138
Oil at 350 K is flowing over a flat plate maintained at 425 K. Tha plate is 0.75 m long and 200 mm wide. The velocity of flow is 0.25 m/s. The properties are evaluated at the mean temperature of 350 deg C. Properties of the oil are v = 50×10^-6 m^2 / s , k = 0.14 W / m - K Pr = 600 , p = 853 kg /m^3. The Nusselt number is most nearly:
What is the Reynolds number of a fluid flowing in a tube with an inside diameter of 2 inches? The viscocity is 1.358 x 10^-5 lb/ft-s and the mass flow rate is 73 lb/h.
Oil at 350 K is flowing over a flat plate maintained at 425 K. Tha plate is 0.75 m long and 200 mm wide. The velocity of flow is 0.25 m/s. The properties are evaluated at the mean temperature of 350 deg C. Properties of the oil are v = 50 x 10^-6 m^2/s, k = 0.14 W/m-K, Pr = 600, p = 853 kg/m^3. The Nusselt number is most nearly:
The liquid food is flowed through an uninsulated pipe at 90 ° C. The product flow rate is 0.3 kg / s and has a density of 1000 kg / m³, specific heat 4 kJ / (kg K), a viscosity of 8 x 10-6 Pa s, and a thermal conductivity of 0.55 W / (m) K). Assume that the change in viscosity is negligible. The internal diameter of the pipe is 30 mm with a thickness of 3 mm made of stainless steel (k = 15 W / [m ° C]). The outside temperature is 15 ° C. If the outer convective heat transfer coefficient is 18 W / (m² K), calculate the heat loss at steady state per meter pipe length. a. Find the convection coefficient in pipe = W / m² ° C. b. Calculate heat loss per meter pipe length = watts