QUESTION 7A refrigeration cycle operates between the freezer compartment at 268K and the ambient air at 295K. The rate of heat transfer from the freezer compartment is 8000 kJ/h and the power input for the cycle is3200 kJ/h. Determine the entropy production for this cycle in kJ/K-h (do not convert h to s). Enter the answer without units, but with a minus sign if applicable.QUESTION 8This cycle operatesⒸ irreversiblyO reversiblyO impossibly.

7.To find Entropy production for the cycle 8. How does cycle operates

Answered: ale or n. Determine the entropy…

ale or n. Determine the entropy production for this cycle in kJ/K-h (do not convert h to s). Enter the answer without units, but with a minus sign if applicable.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

18. For the steam turbine cycle shown to the right, water leaves the closed feedwater heater as saturated liquid and water is extracted from the steam turbine, in mixture form, for use in the closed feedwater heater. Determine TTD of the closed feedwater heater. a. T₁-T₂ b. Ts-T₂ c. Te-T₂ d. T7-T₂ FWH B: Boiler T: Turbine C: Condenser 3 P: Pump FWH: Closed Feedwater Heater
QUESTION 1 An Automotive Engineering company has à task to setup a diesel engine for a new vehicle model. The engine has four-cylinder, four-stroke and 3 liters of displacement volume that operates on the ideal diesel cycle with a compression ratio of 17 as shown in Figure 1. The engine uses light diesel fuel with a heating value of 42,500 kJ/kg and an air-fuel ratio of 24. You are the engineer in the company is given the following task to analyze the engine characteristics based on constant specific heats at 500 K, a) Evaluate all the working temperatures and pressures al all points on P – V diagram. b) Evaluate the thermal efficiency of the cycle. c) If the engine is plan to operate at 3000 rpm, evaluate the power rating produce by the engine. TDC BDC Displacement Clearance volume volume Figure 1
Thermodynamics (Brayton Cycle) Round up the answer up to 5 decimal places. A 120 MW gas turbine power plant running on Ideal Brayton cycle has the followinginitial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature atthe turbine entrance is 910°C. Determine the following: a. Pressure & temperature at each stateb. T-S diagramc. Heat Added, per unit massd. Thermal Efficiencye. Mass flow rate, kg/min
Provide a complete given and computation. Include all the decimals. An ideal reheat regenerative turbo-generator unit receives 9.0 MPa of throttle steam at 390°C.Reheat occurs at the first bleeding point of 3.40 MPa. The second and third extractions are at 0.98 MPa and 0.28 MPa, respectively. For a condenser vacuum of 550 mm Hg, find (a) the cycle thermal efficiency and (b) the engine thermal efficiency.
Step 3 Determine the thermal efficiency of the cycle. n = Save for Later % Attempts: 0 of 4 used Submit Answer
Steam enters the high-pressure turbine of an ideal reheat Rankine cycle at 10 MPa and 500°C. The low- pressure turbine inlet admits steam at 1 Mpa. Assume that the pump inlet is a saturated liquid at 10 kPa and that 80 MW of power is produced overall. QUESTION 1 Using the property tables for both the inlet and outlet of the pump, determine the enthalpy in kJ/kg of the pump outlet. Report your answer to two decimal places using rounding. QUESTION 2 Report the amount of heat added, in kJ/kg, in the boiler before the high-pressure turbine to one decimal place using rounding. QUESTION 3 Report the amount of work produced in the high- pressure turbine, in kJ/kg, to one decimal place using rounding.
1:44 A e-learning.hct.edu.om P Flag question Calculate the heat supplied to the working fluid in a Rankine cycle with reheat. Assume that the working fluid is at superheated condition entering and leaving both HPT and LPT. The working fluid entering the boiler at enthalpy 384.31 kJ/kg leaves boiler at 3.5 MPa and 242.6 °C. The working fluid enters the reheater at enthalpy 2799.5 kJ/kg leaves reheater at 3.5 MPa and 242.6 °C. Paragraph I Path: p Maximum file size: 5OMB maxımum number of II !!!
Provide a complete given and computation. Include all the decimals. Consider a water-ammonia binary vapor cycle consisting. In the steam cycle, superheated vapor enters the turbine at 7 MPa, 450oC, and saturated liquid exits the condenser at 55oC. The heat rejected from the steam cycle is provided to the ammonia cycle, producing saturated vapor at 45oC, which enters the ammonia turbine. Saturated liquid leaves the ammonia condenser at 1 MPa. For a net power output of 24 MW from the binary cycle, determine (a) the mass flow rates for the steam and ammonia cycles, respectively, in kg/s, (b) the power output of the steam and ammonia turbines, respectively, in MW. (c) the rate of heat input to the ammonia cycle, in MW,
Determine maximum temperature of the cycle for the given question
Provide a complete given and computation. Include all the decimals. Consider a water-ammonia binary vapor cycle consisting. In the steam cycle, superheated vapor enters the turbine at 7 MPa, 450oC, and saturated liquid exits the condenser at 55oC. The heat rejected from the steam cycle is provided to the ammonia cycle, producing saturated vapor at 45oC, which enters the ammonia turbine. Saturated liquid leaves the ammonia condenser at 1 MPa. For a net power output of 24 MW from the binary cycle, determine (a) the rate of heat addition to the binary cycle, in MW, and (b) the thermal efficiency of the binary vapor cycle.
Read the questions carefully and answer with complete solution and units.Use the steam tables provided and use 4 decimal places for solving. Draw the T-S diagrams properly with respect to the saturation line. Consider a steam power plant operating on the ideal Rankine cycle.The boiler is maintained at 4 MPa, and the condenser at 10 kPa. The steam quality leaving the turbine is at 80%. a.) Draw the proper T-S diagram of the cycle with proper label for the points. b.)Find the temperature of the steam entering the turbine,Qa, Qr, Wt,Wp, Wnet,efficiency, and steam rate. Final answers must be: 367.45°C,2939.58??/??,1914.24??/??,1029.37??/??,4.03??/??,1025.34??/??,34.88%,3.51??/??ℎ
Read the questions carefully and answer with complete solution and units.Use the steam tables provided and use 4 decimal places for solving. Draw the T-S diagrams properly with respect to the saturation line. Consider a steam power plant operating on the ideal Rankine cycle.The boiler is maintained at 4 MPa, and the condenser at 10 kPa. The steam quality leaving the turbine is at 80%. a.) Draw the proper T-S diagram of the cycle with proper label for the points. b.)Find the temperature of the steam entering the turbine,Qa, Qr, Wt,Wp, Wnet,efficiency, and steam rate