All bars in the truss have the same cross section and material properties. Find the total change in length of the cord A-B-C, and the stress at point p in the coordinate system given. AABC = σ= in ksi A = 0.64 in ² E = 30000 ksi V = 0.29 point p A 800 lb. Y Ľx 5 ft B [1200 lb 5 ft C F 900 lb 800 lb 4 ft 4 ft

All bars in the truss have the same cross section and material properties. Find the total change in length of the cord A-B-C, and the stress at point p in the coordinate system given. AABC = σ= in ksi A = 0.64 in ² E = 30000 ksi V = 0.29 point p A 800 lb. Y Ľx 5 ft B [1200 lb 5 ft C F 900 lb 800 lb 4 ft 4 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

DEFORMATION DUE TO AXIAL FORCES PROBLEM 1: CE Brd Exam The rigid block shown weighs 176.4 kN. It is held in position shown with stress in the supporting rods shown initially zero. If the former is to remain horizontal when released, 1a. Find the ratio of forces in bronze and steel a. 0.389 c. 0.397 1b. Find the stress in the bronze rod. b. 0.344 d. 0.416 а. 31.92 MPа с. 28.73 МPа 1c. Find the the elongation of steel rod. b. 53.34 MPa d. 39.67 MPa a. 0.615 mm b. 1.83 mm c. 2.31 mm d. 2.12 mm 0.6 m BRONZE A=900mm STEEL STEEL A=600mm A=600mm 1 m E-200GPA E-83GPA E=200GPA W = 176.4 kN
8. A rigid bar AB is supported by three rods. A load P = 250 kN is applied to the bar. The modulus of elasticity of copper is 110 x 10°6 kN/m^2 and modulus of elasticity of steel is 200 x 10°6 kN/m^2. Steel rod A= 900 sq. mm Steel rod A= 900 2m sq. mm Copper A=1200 sq. mm 2m B 1m 1m Determine the deformation in the rods (in mm). * Your answer
D 140 mm in the trusses analyies experiment we got the strain Reading as, B Loaden) 5train AB strain AC 5train BC (EM) (EM) (EM) O 469 1117 1116 50 465 1115 1126 100 463 1110 1131 150 458 1095 1139 200 453 1085 250 450 1080 calcute the force in each member; F= πTd²x ExE 4 d = 5.985mm E = 210 GN/m² B W с 1148 t 155
Q.2 The bar is made of an aluminium alloy having a stress-strain diagram that can be approximated by the straight line segment shown. Assuming that this diagram is the same for both tension and compression, determine the moment the bar will support if the maximum strain at the top and bottom fibers of the beam is E max = 0.05. 630 560 420 (MPa) 0.006 0.025 0.05 100mm M € (mm/mm) 75mm
2.47 The negligible weight rigid bar is pinned at O and attached to two vertical rods. WI is the largest load P that can be applied without exceeding stresses of 150 MPa in t steel rod and 70 MPa in the bronze rod, assuming the rods were initially stress-free? 4m 3m 3m Steel A = 600mm2 E = 83Gpa L = 4m Steel V P A = 1800mm2 E = 200Gpa L 3m
A rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free, what is the largest load P that can be applied without exceeding stress of 150 MPa in steel rod and 70 MPa in bronze rod. 2 m -1.5 m |+1.5 m→ 10 Bronze A = 300 mm2 E = 83 GPa Steel A = 900 mm2 E = 200 GPa L=2 m L= 1.5 m
3. The rigid bar AC is pinned at A and attached to bars DB and CE as shown in the figure. The weight of AC is 50 kN and the weights of the other two bars are negligible. Consider the temperature of both bars DB and CE to be raised 35°C. Find the resulting normal stresses in these two bars. DB is copper for which E = 90 GPa, ? = 18 × 10–6 /°C, and the crosssectional area is 1000 mm2 , while CE is steel for which E = 200 GPa, ? = 12 × 10–6 /°C, and the cross section is 500 mm2 . Neglect any possibility of lateral buckling of the bars.
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. BRONZE L-5 m A 500 mm E-80 GPa STEEL L-4 m A-400 mm E-200 GPa 3 m. 5 m. VP
Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1600 mm?. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 т 10 m 10 m K 6 т G H 6 m 15° 15° 40 kN 50 kN E F 6 т б т А B
Question #4: Determine the state of stress at point A on the cross section of the beam at section a-a. Show the results in a differential element at the point. O 2. T a 0.5m 0.5m 30 kN 2 m 100mm 50mm I 10mm 10mm 180mm Section a-a 10mm
An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E= 70000 MPa. The length of each bars are follow: B1 0.8 m; B2 = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B1 in MPа. 35KN B1 B2 ВЗ 10KN 15KN 30KN A 218.75 В 125 (c) 62.5 31.25
The nut on a bolt is tightened by applying a force of P = 50 lb to the end of a wrench at a distance of a = 4.0 in. from the axis of the bolt. The body of the bolt has an outside diameter of d = 0.375 in. What is the maximum torsional shear stress in the body of the bolt? Answer: Tmax= i psi