An amplifier has a voltage gain of 10, an input resistance of 1M ohm and an output resistance of 10. The amplifier is connected to a sensor that produces a voltage of 1V and has an output resistance of 1k, and to a load of 50,. What will be the output voltage of the amplifier (that is, the voltage across the load resistance) ? Source Amplifier Load R, = 1k0 R,= 10 2 R, 1MQ RL 50 2 Select one: O a. Vo = 10V O b. VO=5.6 O c. VO=8.3 O d. VO = 9.3

An amplifier has a voltage gain of 10, an input resistance of 1M ohm and an output resistance of 10. The amplifier is connected to a sensor that produces a voltage of 1V and has an output resistance of 1k, and to a load of 50,. What will be the output voltage of the amplifier (that is, the voltage across the load resistance) ? Source Amplifier Load R, = 1k0 R,= 10 2 R, 1MQ RL 50 2 Select one: O a. Vo = 10V O b. VO=5.6 O c. VO=8.3 O d. VO = 9.3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a DC-DC converter of the circuit with the following specifications: Input voltage (12-40) V; output voltage 24 V; output current is varied from (2 to 4)A: C.C.M with output voltage ripple not more than 1%. Knowing that the switching frequency is 25 kHz. Also draw the current waveforms. And give the Design specifications of diode (PIV, and Vavg ,I peak) and (V Diod , I Diod) of Diode. Buck Boost Converter lin ip + T | Va R ic i.
2. The bridge rectifier circuit has AC source Vrms=230V at 50Hz and there is a series RL load with R=50 Q and L=100mH in the output. (a) draw the circuit and draw input and output characteristic voltages and currents. (b) Determine the output average current.
Plot the graphs of the outputs of the circuits in scale according to the input signal.and provide information about varactor structure and usage areas
Draw the circuit diagram for a full-wave bridge rectifier with a resistance as the load.
what is the difference of MOSFET and Diode in Boost Converter. Can you also sight an example?
Q10. Determine maximum and minimum value of Zener current if value of series resistance is 1 K, load resistance is 2KN and input varies from 10V to 30V. Zener voltage is 5 V. Q11. What is LED? Q12. Which materials are used in manufacturing of LEDS?
Q2: A full-wave bridge rectifier is connected with RC load at frequency 50 Hz. The value of shunt capacitor and the dc output voltage are 0.450 mF, 16.5 V, respectively. The dc output current is 250 mA. What is the peak value of output voltage?
How do we know that with amplification with emitter degenerate resistor amplifier both M1 and M2 are in the saturation region?
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
1. A certain phototransistor has a BDC. 150. If I = 250, what is the collector current? 2. In the figure below, if Vcc is replaced from a 12-V to an 18-V source. what would be output voltage when (a) the light source is OFF and (b) when the light source is ON. #12 V
A 4.7 zener diode is connected to the base resistor. The left side of the resistor sits at about 12V. The right side of the biasing resistor is connected to the Zener and npn transistor. The Zener bias is 5mA. The base current needed is 80uA. What is the appropriate resistor for this circuit? (In kohms) I
Set up a midpoint bias for a JFET with IDSS = 14 mA and VGS(off) = -10 V. Use a 24 V dc source as the supply voltage. Show the circuit and resistor values. Indicate the value of ID. Indicate the value of VGS. Indicate the value of VDS.