An open vessel in the form of a frustum of a cone with a radius of 1.2m (bigger base) on top, the smaller base has a diameter of 1m, and its sides has slope of 1H:3V is full of water. How fast in rpm should it be rotated about its own vertical axis so that b-1. 2/3 of its volume will be spilled? b-2. determine the total height of the paraboloid form for this condition

An open vessel in the form of a frustum of a cone with a radius of 1.2m (bigger base) on top, the smaller base has a diameter of 1m, and its sides has slope of 1H:3V is full of water. How fast in rpm should it be rotated about its own vertical axis so that b-1. 2/3 of its volume will be spilled? b-2. determine the total height of the paraboloid form for this condition

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.113P: Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels...

See similar textbooks

Similar questions

Determine the volume of the concrete arch dam.
Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels are 16 ft on the upstream side and zero on the downstream side. For water, use =62.4lb/ft3.
The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of the filled bowl. Approximate the bowl as a thin shell of radius R=6.15in. Use 1=162lb/ft3 for glass and 2=62.4lb/ft3 for water.
A 6-in. diameter hole is drilled in the conical frustum. Calculate the volume and the surface area of the resulting body.
1-The point of action of the result force is below the centroid, why? 2-If we change the water to some other fluid,such as oil, does the magnitude of the result force and its location change? why? 3-What is the applications of this experiment? 4-Explane why the tank take the shape of quadrant? 5-Discuss the sources of error? 6-Plot ,find the slope, and discuss the results for both cases
Thank you
1. An open hemispherical vessel with a radius of 1.2m is full of oil (0.85) a. How fast in rpm should it be rotated about its own vertical axis so that 2/3 of its volume will not be spilled? b. weight of the remaining liquid after the rotation C. what angular speed in rpm will cause a zero pressure at the center bottom of the vessel?
The system in Fig. is at 20 ° C. Determine the heighth of the water in the left side.
A glass tubing consist of 5 vertical stems which are 500 mm apart connected to a single horizontal tube. The tube is filled with water to a depth of 500 mm in the vertical stems. How fast should it be rotated about an axis through the middle stem to just zero the depth of water in that stem? Ans: o = 42.3 rpm %3D
plzzzzzzzz heeeelp meeee right nowww What would be the rotation rate (in rad/sec) if during rotation the water in the right leg (with a diameter of d) decreases a distance h1=0.10 m?
An open 0.6 m diameter tank contains water to a depth of 0.9 m when at rest. If the tank is rotated about its vertical axis with an angular velocity of 180 rev/min, what is the slope of the water surface at a point 100 mm from the vertical axis? * O 4.68 3.62 O 10.89 O 6.38
The image is for number 1 1. Referring to the figure, a cylindrical column of height equals 5 800 cm has a 115 cm radius. It contains blood with a density equal to 1.06 g/cc. Calculate the volume of the cylinder. Calculate the mass of the blood. Calculate the weight of the blood. Find the force exerted by the air on the disk of radius 115 cm at the surface of the blood. What pressure at a depth of 5 800 cm supports the blood column?