Analyze each problem carefully. Provide FBD and show complete solution clearly. The loaded beam and its cross-section are shown below. Use M = 25 kN-m and = 45 kN/m. M 0.2 m 0.3 m B 150 mm 50 mm a. Determine the support reactions b.Determine the internal shear 0.2 m from the left support. c.Calculate the centroid of the cross-section measured from the bottom 150 mm

Analyze each problem carefully. Provide FBD and show complete solution clearly. The loaded beam and its cross-section are shown below. Use M = 25 kN-m and = 45 kN/m. M 0.2 m 0.3 m B 150 mm 50 mm a. Determine the support reactions b.Determine the internal shear 0.2 m from the left support. c.Calculate the centroid of the cross-section measured from the bottom 150 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the figure it is holding the BCD rod, the AC rod suspended. The cross section of the AC rod is 15 x 8 mm2. 1.6 tons of force is applied to the BCD rod at point D. C pin is single acting and its diameter is 10 mm. According to this; Find the shear stress at the pin and the bedding stress on the AC rod.
2. The lengths LAB = LBC = 200 mm and LCD = 240 mm. The diameter of parts AB and CD of the bar is 25 mm and the diameter of part BC is 50 mm. The shear modulus of the material is G = 80 GPa. What value of the %3D torque T would cause the angle of twist of the right end of the bar relative to the wall to be zero? 4 kN-m A 8 kN-m LAB B T LBC.
The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T 50 lb.ft is applied to it at C, determine the rotation angle that occurs at C relative to A and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst = 11500 ksi, Gbr 5600 Ksi. %3D %3D 3 ft 2 ft 0.5 in. 1 in. T = 50 lb ft
Questions a/b c₁ = c₂ = c 5 0.291 10 0.312 20 0.323 40 0.328 200 10 E m 200 10 1. 6.3 kNm torque is applied to a 3m long steel angle with a 200mm x 200mm x 10mm cross section. From tabulated properties for equal angles, the gross cross sectional area of the section is 5090 mm². knowing that G = 77 GPa, determine (a) the maximum shearing stress along line m-m. Provide the answer in MPa with precision n to two decimal points. 2. Determine the angle of twist if 1.7 kNm of torque is applied to the above long angle steel. Provide the answer in Degrees with precision to two decimal points.
A beam has circular cross-section. Shear stress at a depth of 0.6R from x-x line as kV then kis TR² shown in the figure if the applied shear force at section is Vis centre R
Question 1: Analyze and determine the deflection at the end B of the clamped A-36 steel strip. The spring has a stiffness of k = 2 N/mm. The strip is 5 mm wide and 10 mm high. Also, draw the shear and moment diagrams for the strip. Use the method of consistent deformation in your calculations. 50 N -200 mm B A k = 2 N/mm 10 mm
The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T = 50 lb.ft is applied to it at C, determine the rotation angle that occurs at C relative to A and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst = 11500 ksi, Gbr 5600 Ksi. %3D 3 ft 2 ft 0.5 in. 1 in. T 50 Ib-ft
200mm Strain gauge F mun +100m 200mm- 4mm Strain gauge 4mm 12mm 12mm 4mm A small T-section is used in inverted positions as a beam and is shown in figure over a span of 400 mm. If due to the application of forces shown, the longitudinal strain gauge at F registers a compressive strain of 1500 microstraints, determine the magnitude of P. Take E = 200 GPa.
Determine the maximum bending moment magnitude for the beam shown below. Use a = 18 ft, b = 6 ft, and w = 6 kips/ft. The reaction forces for this beam are Ay = 48 kips and By = 96 kips. %3D W В a b olerance is + 1 in the 3rd icant digit. Mmax ! kip-ft
A single axial load of magnitude P is applied at end C of the steel rod ABC. Knowing that E = 30 x 106 psi, the deflection of point C will be 0.1 in. A 1.25-in. diameter 4 ft B d 3 ft P 7. Determine the deformation of segment AB in inches if P = 44 kips.
the largest axial P force that the given riveted joint can safely carry.calculate. Rivet diameter 32mm and plate width 310mm. Shear stress of the rivet1400 kg/cm2, crush safety stress of rivet 2800 kg/cm2and the platetensile safety tension 1400 kg/cm2will be taken. t1=20mm t2=37mm
1) a. Determine the location of the plastic centroid for the column shown. b. Calculate the design axial load and moment capacities (OP, and Mn), for bending about the x-axis with compression at the top fiber and a tension strain of 0.004 in the bottom layer of steel. f. = 40 MPa, and f, = 420 MPa. 600 mm 300 mm 300 mm 12T25 800 mm 165 mm 150 mm 150 mm 150 mm 65 mm