i need the answer quickly and its position may be established at any point along the load line by a suitablebiasing arrangement.The best possible position for this Q-point is as close to the center position of theload line as reasonably possible, when Vce = 1/2Vcc..Vcc = 12v150k10kO VoutC2Vin15k1kDiscussion1- In amplifier circuit, why biasing of transistor is necessary?2-Which configuration in which current gain of transistor amplifier is lowest?3- For amplification CE is preferred, why?

Answered: Image /qna-images/answer/16076a06-cde9-40a8-963b-f9b224594450.jpg

and its position may be established at any point along the load line by a suitable biasing arrangement. The best possible position for this Q-point is as close to the center position of the load line as reasonably possible, when Vce 1/2Vc.. o Vcc = 12v 150k 10k O Vout C2 Vin 15k 1k Discussion 1- In amplifier circuit, why biasing of transistor is necessary? 2-Which configuration in which current gain amplifier west? 3- For amplification CE is preferred, why?

and its position may be established at any point along the load line by a suitable biasing arrangement. The best possible position for this Q-point is as close to the center position of the load line as reasonably possible, when Vce 1/2Vc.. o Vcc = 12v 150k 10k O Vout C2 Vin 15k 1k Discussion 1- In amplifier circuit, why biasing of transistor is necessary? 2-Which configuration in which current gain amplifier west? 3- For amplification CE is preferred, why?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A Bipolar junction Transistor with curreat amplification factor being 100, Input Base current is 50μA. Collector voltage is 10 V and biasing voltage being +20 V. Find followings a. Collector current b. Resistance (R1) c. Collector voltage , Emitter voltage , Base Voltage & Collector-Emitter Voltage.
4 For the transistor shown in below figure, Calculate the value of R, that will just make the transistor work as closed switch. Hence Bpc= 80, VBE = 0.7V, VCE(sat) = 0.2V, Vcc= 12V, Rc= 2.7KN. la) Calculate the In and I.. Vcc RB Rc |b) Calculate Rp- B'
(a)(i) State three differences between the Field Effect Transistor (FET) and the Bipolar JunctionTransistor (BJT). (ii) Draw the physical structure and device symbol for an n-channel JFET. (iii) What is meant by drain characteristics (b) Determine the drain current of an n-channel JFET having pinch-off voltage VP = - 4 and drain-source saturation current IDSS=12mA at the following gate-source voltages(i) VGS= 0V(ii) VGS= -2V (c) Calculate the transconductance, gm of a JFET having specified values of IDSS=12mA and VP= - 4V at bias points(i) VGS= 0V and(ii) VGS= -1.5V.
Design the fixed bias circuit from the load line given in the figure below. Ic sat. =10mA IB=60UA Vcc= 20v VCE
Q1. (a) Consider the amplifier circuit in Figure Q1(a). Given the following: RI = 100 k2 R2 = 56 kN Rc =2 k2 Vcc = +8 V Assume the transistor has B = 100 and VBE(on) = 0.7 V. You may neglect Early effect and use VT = 26 mV. (i) Draw the DC equivalent circuit, then determine Iç and VCE. Draw the AC equivalent circuit using re model. Based on this, determine the parameters Av, Rin and Rout. (ii) Vcc Rc R1 R2 C3 Vout C2 Ci Vin Figure Q1(a)
C-A transistor supplies 2W to 4k2 load. The zero signal collector current is 35mA and the D.C. collector current with signal is 39mA. Determine the second order harmonic distortion.
a) What circuit elements ensures that a common source n-channel JFET amplifier has a ac voltage gain?
How to calculate the bias resistor of a common emitter amplifier. The design curretn is 0.55mA. Bera is assumed to be 200 and the Vcc = 12V. Note: the bias resistor should be high.
1 a) Write down the equation that relates the collector current of the bipolar transistor to the base-emitter voltage. Hence prove the relationship 9mbe Bowhere the ac parameters are transconductance, base-emitter resistance and ac current gain respectively. c) Draw a schematic diagram of a simple current mirror circuit. Show how it can be extended to form a current repeater. How can the current repeater be improved to allow different bias currents to be realised?
TRANSISTOR BIAS DESIGN AND STABILITY Explain Why is it that decreases of the input resistance of the amplifiers not a problem for a single-diode temperature compensation or two-diode compensation circuits such as constant current sources used in integrated circuits?
How base width vary in Transistor amplifier Circuits? Explain in detail and how this modulation affects the input and output characteristics of CE configuration.
Determine the folowing A.base current (IB), B. collector current (Ic), C. collector-to-emitter voltage (VCE),D. draw the load line, locate the Q-pointF. input impedance (Zi),G. Output impedance (Zo)