Apply each of diode approximations given the following parameters:D1: Si, rB = 2 Q, rR = 220 k D2: Si, rB = 5Q, rR = 560 k2 and determinethe current flowing through D1, D2 and R2, R3, the voltage across R3.%3D%3DFinalize answers as follows: Ideal approx:Id1=_, Id2=_,12=13=_, V3=,; 2nd approx: Id1=Id23D12=_13=V3=:3rd approx: Id1=Id2=12= ,13=_,V3=R12.5 kQD1D2R32.5 kå10 VR21 kQ

Answered: Image /qna-images/answer/535afca8-f0df-4261-81cd-f44a9058f49e.jpg

Apply each of diode approximations given the following parameters: D1: Si, rB = 2 Q, rR = 220 k D2: Si, rB = 5Q, rR = 560 k2 and determine the current flowing through D1, D2 and R2, R3, the voltage across R3. %3D Finalize answers as follows: Ideal approx: Id1=_, Id2= _ , 12= 13=_, V3=, ; 2nd approx: Id1= Id23D 12= 12= , 13%= 13= V3= :3rd approx: Id1= Id2= V3= R1 2.5 kQ D1 D2 R3 10 V 2.5 kà R2 1 kQ

Apply each of diode approximations given the following parameters: D1: Si, rB = 2 Q, rR = 220 k D2: Si, rB = 5Q, rR = 560 k2 and determine the current flowing through D1, D2 and R2, R3, the voltage across R3. %3D Finalize answers as follows: Ideal approx: Id1=_, Id2= _ , 12= 13=_, V3=, ; 2nd approx: Id1= Id23D 12= 12= , 13%= 13= V3= :3rd approx: Id1= Id2= V3= R1 2.5 kQ D1 D2 R3 10 V 2.5 kà R2 1 kQ

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

Q1 Assume that each diode has a turn-on voltage 0.7V in the circuit shown in Figure Q1. By using the constant voltage drop model: 1kN D1 D2 2kN 4k2 6V 3V 4V Figure Q1 a) Show that it is not possible that D1 is on and D2 is off. (Hint: show a contradiction) b) Show that both D1 and D2 are on.
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
uO 9:.0 A docs.google.com * ZAIN IQ l. Q3/B: Assume an ideal diode model for all the diodes in the circuit below. calculate voltages and currents through D1 and D2 9kQ 1N1199C R2 D1 18KQ 1N1199C D3 1N1199C V2 =12 V R3 1kQ R4 5kQ 1.22 V 11 mA 0.5 A O VD1 ID1 VD2 ID2 صفحة 4 من 6
In the figure given we have u(t)=10. cosot [V]. We assume the diodes and the A-meter (A) to be ideal. A u(t) a) Plot the waveform of the current flowing through the A-m in scale. b) What is the reading of the A-m, if it is moving-coil type? c) What is the reading of the A-m, if it is moving-iron type? d) Calculate the power factor of the WHOLE structure. R1 1 R2 102
points) For the circuit shown below, sketch to scale the output V, waveform and draw the transfer characteristic (V. versus Vi), Assume the diodes are ideal. V₁ =15-sin wt Zloks www loks # HIF 4V + Vo
In the circuit given in the figure, find the current passing through the diode in mA since R1 = 4.95Kohm, R2 = 2.50Kohm, R3 = 1.69Kohm, R4 = 5.44Kohm, VCC = 13.00V and the diode is silicon?
A diode circuit is given in the below figure, in which two diodes are connected in series and their saturation currents are Is1 =10-¹6 A and Is2 =10-¹4 A. If the applied source voltage is 1 V, calculate the currents IDI and ID2 and the voltage across each diode VDI and VD2. IDI Ī Vpl + D₂ VD2
Consider the circuit in the figure below 4:1 120 V rms ooooo gll reelee D₁ L a. What type of circuit is this? b. What is the total peak secondary voltage? D₂ c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? RL 1.0 ΚΩ
C. In the circuit shown below the knee current for the ideal Zener diode is 10 mA Calculate the minimum value of load resistance RL in order to maintain 5 volts across the load resistance RL 2. WW-
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
Draw the characteristics of Ideal and practical diodes. A semiconductor has electron and hole mobilities as Hn = 7500 cm³ /V. sec, Hp = n = 3.6 x 1012 cm-3. Find (i) The hole concentration when conductivity is minimum. (ii) The minimum conductivity. 300 cm /V.sec and
Suppose we have a 10-V-peak sinusoidal voltage source. Draw the diagram of a circuit that clips off the part of the sinusoid above 5 V and below -4 V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. Be sure to label the terminals across which the clipped output waveform vo(t) appears.