As a machinist presses the handles of the compound action bolt cutters, link AB carries a 7.2 kN force. If the link has a 15 x 3-mm rectangular cross section, calculate the tensile stress within it.PF(Express your answer using three significant figures.)|MPa

Answered: Image /qna-images/answer/b4723991-14ad-48be-97c9-f24ffd80efc6.jpg

Answered: As a machinist presses the handles of…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's Circle determine the maximum normal stress on the element. Use rubric as per usual. 20 MPa 50 MPa 30 MPa 30 MPa 50 MPa 20 MPa
Determine the stress area in mm2 of a 1.75 - 8UNC bolt.
Determine the state of stress at point q. The pipe has an inner diameter of D₁ = 1.0 in and an outer diameter of = 1.8 in. Use the exact expression for Q, if needed. Label the reultant forces on the cross section below. Report your answer (3x3 matrix) in psi to one decimal place. Do 4 in. Y 4 in. 150 lb 6 in. 50 lb 10 in. 200 lb 150 lb X N Y
1-63.M. The key in Figure 1-18 has the dimensions b = 10 min, h = 8 nim, and L = 22 min. Determine the shear stress in the key when 95 N-m of torque is transferred from the 35-mm-diameter shaft to the hub. Hub End view Shear plane Shear pl T=Torque -D=Shaft diameter T=F(D/2) F₁-Force of shaf F₂= Force of hub on 1 Shear area=A,=bxL
The shear stress is maximum on the principal plane Select one: O True O False
One shaft is in torsion as shown below. If the magnitude of shear stress at point A is 345.6 MPa, calculate the magnitude of the shear stress at point B on the same cross-section as point A: MPa. Calculate your answer to 1 decimal place. 40 mm 30 mm T
Draw and stress tensonr with the following characteristics The stress cube visualization at point A would depict the normal stress (σ_x) acting on two opposite faces and the shear stress (τ_xy) acting tangentially on the four sides associated with torsion.
Direct a key d the Hub Shear plane Hub Key F2 y, or anical F1 T=Torque Shaft T=F(D/2) F = Force of shaft on key F= Force of hub on key Side view -D Shaft diameter End view Shear Shaft plane Hub F1 Key F2 Shear area = A, = bxL %3D Enlarged view of key Pictorial sketch of key, shaft, and hub Ноу
For the stresses given with the cube below: 1. Compute the center, radius (R), principal normal stresses (0₁ and 03), max shear stress (Tmax) and draw the Mohr's Circle. 2. Compute the normal and shear stresses when the cube is rotated 20° clockwise from the horizontal plane and draw them on the cube. 3. The yield point stress (σyp) is 6 kPa. Determine if the material will fail under stresses shown using Tresca's Hexagon. вкра акра 6 экра 8 кра экра 4кра
Rank the normal stress in each section of the bar. Rank the values of normal stress from largest (largest tensile stress) to smallest (largest compressive stress). Use AB for segment AB, BC for segment BC, and CD for segment CD.
If P is equivalent to 94 kN, the diameter at pin B is Blank 1 mm.
Determine the resulting maximum value of the normal stress. Specify the orientation of the plane on which these maximum values occur. **The answer is tensile stress is 0 ksi at 90 degrees. **The answer is compressive stress is 7 ksi at 0 degrees. Can you explain how that is? This was my thought process: I know that tensile would be zero because the force P is actually going inwards and not outwards. I know that means that there would be a compressive force. I am confused on the angles, how is a tensile force going 90 degress if there technically is no force in the tensile direction. And how is there a compressive force at 90 degrees if there is a stress? thank you!

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

As a machinist presses the handles of the compound action bolt cutters, link AB carries a 7.2 kN force. If the link has a 15 x 3-mm rectangular cross section, calculate the tensile stress within it. F P B (Express your answer using three significant figures.) |MPa