As shown, beam ABC is supported by the roller at A and pin at C. The geometry of the beam is given by a = 5.0 m, b= 6.5 m, and c = 11.0 m. The applied forces are F = 2.75 kN and F2 = 2.00 kN. Force F, is applied at an angle 0 = 60° with the horizontal. Neglect the weight of the beam. (Figure 1) Figure 1 of 1 F1 che В a F2

As shown, beam ABC is supported by the roller at A and pin at C. The geometry of the beam is given by a = 5.0 m, b= 6.5 m, and c = 11.0 m. The applied forces are F = 2.75 kN and F2 = 2.00 kN. Force F, is applied at an angle 0 = 60° with the horizontal. Neglect the weight of the beam. (Figure 1) Figure 1 of 1 F1 che В a F2

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.97P: The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces...

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Beam ABC is supported by a tie rod CD as shown. Two configurations are possible: pin support at A and downward triangular load on AB or pin at B and upward load on AB. Which has the larger maximum moment? First, find all support reactions; then plot axial force (N), shear (V), and moment (M) diagrams for ABC only and label all critical N, V, and M values. Label the distance to points where any critical ordinates are zero.
The inclined beam represents a ladder with the Following applied loads: the weight (W) of the house painter and the distributed weight (u) of the ladder itself. Find support reactions at A and B: then plot axial force (N), shear (V), and moment (M) diagrams. Label all critical N, V, and M values and also the distance to points where any critical ordmates are zero. Plot N, V, and M diagrams normal to the inclined ladder. Repeat part (a) for the case of the ladder suspended from a pin at B and traveling on a roller support perpendicular to the floor at A.
A plane frame is constructed by using a pin connection between segments ABC and CDE. The frame has pin supports at A and E and joint loads at B and D (see figure). (a) Find reactions at supports A and E. (b) Find the resultant force in the pin at C.
plz help before -ront The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T₁ 410-N forces act in the - direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and components of force on the shaft. Figure lashel but sol is 300 mm A 200 mm 2 150 mm 150 mm ✓ 200 mm 400 mm B. 200 N 200 N 80 N 80 N 1 of 1 ▾ Part B Determine the resultant shear force in the y direction on the cross section at C Express your answer to three significant figures and include appropriate units. (Vc)y=245.714 Submit Part C Submit * Incorrect; Try Again; 3 attempts remaining Check your signs. (Vc),= 175 ▾ Part D Determine the resultant shear force in the direction on the cross section at C. Express your answer to three significant figures and include appropriate unite. T= 10 ▾ Part E Previous Answere (Mc) Submit M ^ Part Fi * Incorrect; Try Again; 5 attempts remaining…
Show a free body diagram of the left section. Find the forces in the members listed by the Method of Sections. 1. Find forces in BD, BE and CE. (T C) BD = BE = (T C) CE = (T C) 1200 1800 540 5' A 12 12' 12' 540 2075 1675 300 450 B0
PROBLEM 3: A right-angled rigid pipe is fixed to a wall at A and is additionally supported through the cable CD as shown in the figure. The tension in the cable is 3 kN. Neglect the weight of the pipe. Use the Right-Hand-Rule to indicate the direction of the moment. [8] Calculate total force reaction at A. (ANSWER: 3.00 KN) [9] Calculate the moment reaction (including correct sign) at A about z-axis. (ANSWER: 2.168 KN-m) [10] Calculate the moment reaction (including correct sign) at A about x-axis. (ANSWER: -0.843 KN-m)
In the crane shown, assume that the horizontal arm of the crane weighs 200 kg/m. If a counterweight of 100kN is used, what is the capacity P of the crane? Also find the moment at the base of the crane when no load is being carried (i.e., when P=0). What weight should be added so that the capacity would rise to 8 tons? 130 On-
The elements of a floor jack are shown in the figure. The figure CDFE is a parallelogram. Calculate the magnitude of the force in the hydraulic cylinder AB corresponding to the 2270-Ib load supported as shown. What is the magnitude of the force in link EF? Assume W = 2270 lb, a = 2.90 in., b = 3.10 in., c = 4.45 in., d = 8.75 in., e = 1.95 in., and f = 1.95 in. W e D b. a A E Answers: AB = i Ib EF = i Ib
Ciear Ly A beam (AB) is attached to a roller at A and a pin at B. It is subjected to three concentrated forces as shown in the figure below. The vertical component of reaction at pin B is. 3 kN 2.5 kN 1.5 kN30. 2m- 4 m 2 m- Select one: O a. 4.35 kN O b. 6.15 kN Oc. 3.35 kN O d. 1.25 kN Clear my choice 直0 üull lis sI FUJITSU
Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of ø = 64.0 ° with the floor and rope segment CD creates an angle 0 with the horizontal. If both ropes BCA and CD can support a maximum tensile force Tmaz = 165 lb. what is the maximum weight Wmar of the crate that the system can support? What is the angle e required for equilibrium? Express your answers numerically in pounds and degrees to three significant figures separated by a comma. • View Available Hint(s) nν ΑΣφ vec Wmax.0 = lb, degrees
The truss shown in the figure below is supported on roller at A and a hinge at B. Solve for the | components of reaction. Note: use "m" for distance use "N" for unit of force 600 240 D 16' 12' 12' F 12' BH 400 Ay By MATHalino.com