Assuming that the load P = 120 KN is carried equally by the four rivets in the figure showing the double lap connection, determine the following: (a) the shear stress in the rivets if the diameter of the rivet is 16 mm and (b) the thickness of the inner steel plate if the bearing stress is 132.63 MPa.

Q: The figure shows a roof truss and the detail of the connection at joint B. Member BC and BE are…

A:

Q: Four axial forces are applied to the 25mm thick structural steel bar with 40mm diameter pins as…

A: for solution refer below images,

Q: In the figure below, a pulley can pull a 1-ton load from rest to 3 m/s upwards at 2 seconds. AB and…

A: Given: The load, W = 1 ton The speed, v = 3 m/s The time, t = 2 s The compressive stress, σ = 140…

Q: A bolted single lap joint shown in the figure below is designed to join two sheets of wood using a…

A:

Q: 2. The steel compression link shown in the figure has a rectangular cross section and supports an…

A:

Q: A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If…

A:

Q: Determine the stress in each section of the bar shown in the Figure when subjected to an axial…

A:

Q: From the figure shown, the tube has an outer diameter of 80 mm and an inner diameter of 70 mm.  The…

A:

Q: 2.16 A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in…

A:

Q: A clevis-type pipe hanger supports an 8-in.-diameter pipe, as shown in Figure. The hanger rod has a…

A: Given data: W=2000 lb Need to determine the normal stress in the hanger rod, shear stress in the…

Q: The lap joint shown is fastened by 4 rivets of ¾ in. diameter. Find the maximum load P that can be…

A: Given Data: Diameter of rivet, d=3/4 inch Working shear stress, 14000 psi Working bearing stress,…

Q: Two solid cylindrical bars AB and BC are welded at point B and have loads as shown in the figure. If…

A: Given PAB=200MpaPBC=175Mpa

Q: The assembly shown in Figure consists of an aluminum tube AB having a cross-sectional area of 400…

A:

Q: A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in…

A:

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

A:

Q: 2. For the joint shown in the figure below, calculate (a) the largest bearing stress between the pin…

A: Given Data : Tensile Load P = 25 KN a) Bearing stress between pin and the members σb σb = Pd ×…

Q: The plates of thickness 1.5mm is joint by two 3.0mm diameter rivets as shown in the figure.…

A:

Q: Problem 3 The steel rod shown in the figure is stress- free before the axial loads P1 = 150 kN and…

A:

Q: A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The…

A:

Q: The bell crank, which is in equilibrium under the forces shown in the figure, is supported by a…

A: Given data;- diameter of pin =20 mm Tensile stress in AB = 100 Mpa

Q: 4. [Modified from external source] A pipe with an inside diameter of 35mm is closed by end caps…

A: given data as per question pressure in pipe = 650 pa diameter of pipe = 35 mm diameter of cap = 40…

Q: 100 kN Stiff loading plate 10 cm 10 cm 10 cm 25 cm E= 200 GPa E = 200 GPa E= 70 GPa

A:

Q: A single shear lap-joint connection is shown in the figure, If P-10,825 N, d-22 mm, and t-38 mm,…

A: Given data P=10.825 Nd=22 mmt=38 mm Here, P is the load, d is the diameter and t is the thickness.…

Q: Three solid cylindrical rods are welded together to form the compound axial member shown in the…

A:

Q: Four axial forces are applied to the 25mm thick structural steel bar with 40mm diameter pins as…

A: The given force member is as shown below,

Q: Q3. Two bars of rectangular cross section (thickness t=15 mm) are connected by a bolt in the manner…

A: Given : P = 31 KN thickness, t of the base = 15mm  Allowable shear stress in bolt ζAllow  = 90 MPa…

Q: The lap joint shown in the figure below is fastened by six 20-mm diameter rivets. Assuming that p =…

A:

Q: Shear Stress P 130 mm P 25 mm 25 mm P 5. Assume that the axial load P applied to the lap joint is…

A: Joining of metals or plates can be achieved by the following the method 1) Welding 2) Riveting  3)…

Q: A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The…

A:

Q: Home Work: Determine the largest load P that can be supported by the circular steel bracket shown in…

A:

Q: In the figure, the rivets diameter is Ød = 15 mm in the riveted joint connection. The profile used…

A:

Q: EXH.W.3:- The lap joint shown in figure is fastened by three (23 mm) diameter rivets. Assuming that…

A:

Q: A clevis-type pipe hanger supports an 8-in.-diameter pipe, as shown in Figure. The hanger rod has a…

A: Given data: W=2000 lb Need to determine the normal stress in the hanger rod, the shear stress in the…

Q: For the connection shown in the figure, determine the average shear stress (psi) produced in the…

A: ◆ The average shear stress produced in each of the bolt is 5660 psi. ◆ Therefore, option (b) is…

Q: For a given Data of the riveted joint shown in the figure: Given: Diameter of each rivet = 3/4 inch…

A: Given Diameter of each rivet =34 inch=18.796 mmMaximum allowable shear stress of rivet τy =96.53…

Q: Q2: The pin-connected structure shown in figure below consists of a rigid member BED and three steel…

A:

Q: Question 3: Rectangular bars of copper and aluminium are held by pins at their ends, as shown in the…

A: Answer: The shear stress in the pin is 50.438 MPa.

Q: A uniform bar AB weighing 500 kg is supported at both end by a cable as shown in the figure.…

A:

Q: A steel column of hollow circular cross section shown in Figure is supported on a circular steel…

A:

Q: 7. The bell crank, which is in equilibrium under the forces shown in the figure, is supported by a…

A:

Q: A steel cantilever beam is made of two T-shaped structures welded to each other as shown in the…

A: Given Dataσ=150MPaτ=100MPaq=20MN/m

Q: When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this…

A:

Q: A uniform bar AB weighing 500 kg is supported at both end by a cable as shown in the figure.…

A:

Q: 200 mm 1.36 The bell crank, which is in equilibrium under the forces shown in the figure, is…

A:

Q: A sign for an automobile service station is supported by two aluminum poles of hollow circular cross…

A: here we have to solve this,            The resist a wind pressure (P)=75 lbft2            The height…

Q: The box shown in the figure is assembled by gluing two pieces of plastic together at an angle a. The…

A: Given Data: The load is P. The factor of safety is F.S=1.5 The allowable normal stress is σmax=35…

Q: The figure shows a roof truss and the detail of the riveted connection at joint B. Using allowable…

A: To find: Number of rivets.

Q: Question #4 Bar (1) in the figure has a cross-sectional area of 0.75 in². If the normal stress in…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.