Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. Determine the elongation or reduction of each member if the magnitude of force P is 9 kN. Also, what is the total elongation or reduction of all members? Indicate reduction by adding the minus (-) sign in your final answer.

Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. Determine the elongation or reduction of each member if the magnitude of force P is 9 kN. Also, what is the total elongation or reduction of all members? Indicate reduction by adding the minus (-) sign in your final answer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. At temperature T₁, the two rigidly connected rods just fit the rigid supports. If both sections are identical except for the diameter, prove that the following equations are true when temperature rises to T₂. a. F= b. OAB C. OBC A x(T₂-T₁)лd²E 20 x(T₂-T₁)E 5 9x(T₂-T₁)E 5 -1/2- d B 1/12- d C
Question 1: Given that Tuitow = 50 MPa for the rod AB and tattow = 25 MPa for the rod BC. If T=1250 N.m, find the required radius for both rods. Ahmtmum AB = BC =
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F; - 32 kips. F2 - 10kips, Fs- 24 kips, and F4- 39 kips, determine the absolute value of the axial load in rod (2). O 6 kips O 2kips O 4 kips O 17 kips O 11 kips
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 31 kips, F₂ = 11 kips, F3 = 22 kips, and F4 = 36 kips, determine the absolute value of the axial load in rod (2). F A F₂ (1) F₂ B F3 C (3) D O 16 kips O 12 kips O 7 kips O 9 kips O 22 kips
When the two forces are placed on the beam, the diameter of the A-36 steel rod BC decreases from 40 mm to 39.96 mm. (Figure 1) Figure -1 m -1 m P -1 m- B 0.75 m 1 m Part A Determine the magnitude of each force P. Express your answer to three significant figures and include the appropriate units. P = μA Value KN Submit Previous Answers Request Answer Provide Feedback ? X Incorrect; Try Again; 2 attempts remaining
The bar ABC is supported by a pin at A and a steel wire at B. Determine the magnitudeof force Pinlbif the elongation of the wire is 0.059 in. The cross-sectional area of the wire is 0.0039 inandthemodulus of elasticity of steel is 29001 ksi,X=3.86 ft, Y = 6.78 ft, and L = 5.6 ft. Express the final answer to four decimal places. ... B Y
3. The aluminum block has the rectangular cross-section and is subjected to an axial compressive force of 8 kips. The 1.5-in side changed its length to 1.50014 inches. Use E = 10 x 10³ ksi. Calculate the new length of the 2-inch side. Answer: Lnew = 2.00019 in 1.5 in 2 in. 8 kip- 8 kip 3 in. 4. A solid cylinder of diameter D is subjected to an axial load P. Show that its change in diameter is 8D = 4Pv/лDE.
Required information Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. Given: P₁ = 65 kN and P2 = 40 kN. Take Es = 200 GPa and Eb = 105 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A -180- Dimensions in mm Steel B. -120- P₁ 40-mm diam. J 100 100 DI E Brass P2 30-mm diam. Determine the deflection of point C. The deflection of point C is um (Click to select) (Click to select)
A small stepladder has vertical rails and horizontal steps formed from a C-section aluminum channel. Two rivets, one in front and one in back, secure the ends of each step. The rivets attach the steps to the left and right hand rails. A 225 lb person stands in the center of a step. If rivets are formed of 6061-T6 aluminum, what should be the diameter d of the rivets? Use a factor of safety of 8 and round your answer to the nearest 1/16 of an in.
The axial load 229kN applied to the lap joint is distributed equally among the three 17.1-mm-diameter rivets. What is the maximum tensile stress (in Mpa) in the plate if w=139.6mm and t=29mm? Round off the final answer to three decimal places.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress (in Mpa) in the bronze given that P= 189.3 kN? Express your answer in four decimal places.
The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.31 in2. Find the vertical displacement (in inches and absolute value) of point Coaused by the 2888-lb load if x = 8.7 ft and 8 = 46.5-. Use E = 29159 ksi for steel. Note: Round off the final answer to four decimal places. Rigid B P