(b) An unbalanced three-phase, delta connected load is connected to a three-phase star connected supply of 240 Vrms per phase. The phase sequence is positive. The loads is given as below: Taking VRY as reference. (i) (iii) ZRY=30/0° ZYB40236.87° ZBR=452-10° 2 Sketch and completely label the full circuit. Determine the line currents. Determine total apparent power (S), active power (P) and reactive power (Q) delivered by the source.

(b) An unbalanced three-phase, delta connected load is connected to a three-phase star connected supply of 240 Vrms per phase. The phase sequence is positive. The loads is given as below: Taking VRY as reference. (i) (iii) ZRY=30/0° ZYB40236.87° ZBR=452-10° 2 Sketch and completely label the full circuit. Determine the line currents. Determine total apparent power (S), active power (P) and reactive power (Q) delivered by the source.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.25P: Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows:...

See similar textbooks

Similar questions

Determine the positive- and negative-sequence phase shifts for the three- phase transformers shown in Figure 3.36.
Three single-phase two-winding transformers, each rated 25MVA,34.5/13.8kV, are connected to form a three-phase bank. Balanced positive-suence voltages are applied to the high-voltage terminals, and a balanced, resistive Y load connected to the low-voltage terminals absorbs 75 MW at 13.8 kV. If one of the single-phase transformers is removed (resulting in an open connection) and the balanced load is simultaneously reduced to 43.3 MW (57.7 of the original value), determine (a) the load voltages Va,Vb, and Vc; (b) load currents Ia,Ib, and Ic; and (c) the MVA supplied by each of the remaining two transformers. Are balanced voltages still applied to the load? Is the open transformer overloaded?
The direct electrical connection of the windings allows transient over voltages to pass through the auto transfonner more easily, and that is an important disadvantage of the autotransformer. (a) True (b) False
Consider three ideal single-phase transformers (with a voltage gain of ) put together as three-phase bank as shown in Figure 3.35. Assuming positive-sequence voltages for Va,Vb, and Vc find Va,Vb, and VC. in terms of Va,Vb, and Vc, respectively. (a) Would such relationships hold for the line voltages as well? (b) Looking into the current relationships, express IaIb and Ic in terms of IaIb and Ic respectively. (C) Let S and S be the per-phase complex power output and input. respectively. Find S in terms of S.
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
Power factor correction is usually done by adding _________ to the load circuit.Select the correct response:a. switchb. capacitorc. inductive loads
Power in a three phase delta system with balanced load is equal to (Sqrt (3)) (VL) (IL) (p.f.) (Sqrt (3)) (Vph) (Iph) (p.f.) (Sqrt (3)) (VL) (Iph) (p.f.) O (Sqrt (3)) (Vph) (IL) (p.f.)
Connect three single-phase transformers in Y-Y, with subtractive polarity, so that the line-to-line voltages on the primary are 30 degrees delayed to their respective line-to-line voltages on the secondary. It should show each step that is needed to make this connection (example: the phasor diagram) and should show the final connection of the three transformers including the polarity markings. Assume phase A on the primary is terminal "H1".
Calculate the initial symmetrical short circuit current that will occur when a 3 phase short circuit error occurs at the F point in the Figure below İ k3 phase-max ?
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
Q2 (a) Three-phase generator consist of three set of single-phase generators, with voltages equal in magnitude but differing in phase angle by 120° apart. (i) Sketch phasor diagram of the three-phase voltages VA, VB and Vc (ii) Plot the three-phase voltages waveform in Q2(a)(i) in single plot.
A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase. For the leading phase the load has a resistance of (13.3 ohm) and capacitor of (318) micro farad in series. For the other phase the load consists of resistance (10) ohm and an inductance of (42.3) mH. Calculate both mathematically and graphically the lines currents on 3- phase side. The main transformer primary to secondary turns ratio is (12/1).