a) For a DC Power Supply, having a voltage of 50 V, design circuits which can give the following output voltages: i) 10 Volts ii) 25 Volts iii) 45 Volts Draw the labelled circuit diagram for each output voltage value and show calculations for all. Use R1 = 4.7 kQ for one of the resistance Hint: Use voltage divider circuits, you can use any value of resistances you like.

a) For a DC Power Supply, having a voltage of 50 V, design circuits which can give the following output voltages: i) 10 Volts ii) 25 Volts iii) 45 Volts Draw the labelled circuit diagram for each output voltage value and show calculations for all. Use R1 = 4.7 kQ for one of the resistance Hint: Use voltage divider circuits, you can use any value of resistances you like.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 4PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Suppose the three branch currents in this circuit are I₁ = -3 A, I₂ = -18 A, and I3 = -15 A. The voltage drop across each circuit element is as given in the table below. From this information, determine, for each of these circuit elements, (i) whether an active or passive sign convention is being used for that element, (ii) whether that element is absorbing or producing a net (positive) amount of electrical power. In each answer box within the table below, type the correct choice from among the bold-faced words above. V₂ B A B A C D 1₁ A B 1₂ 1₂ + Circuit element Voltage drop Sign convention? Absorbing or producing net electrical power? -9 V -2 V C 9 V -11 V D
For the circuit below, determine the resistor voltage. The source is 6 volts, the Zener potential is 5.1 volts and the resistor is 1k.
For the circuit below, determine the resistor current. The source is 8 volts, the Zener potential is 5.2 volts and the resistor is 5k ohms.
Three types of electric device A,B, and C are connected in series across a 115-volt a-c source, and the voltage drops across the individual units are equal. If Eb leads EA by 90 elec deg and Ec lags behind by 90 elec deg, what are the emds across A,B,C? Ans: EA = EB = EC = 115 Volts
How do I solve this using Kirchoff's Voltage Law?
a) Graphically show the differences between alternating current voltage (A.C) and direct current voltage (D.C). What are the advantages of A.C compared to D.C?
For the series-parallel arrangement shown in the Figure below, find (a) the supply current, (b) the current flowing through each resistor and (c) the p.d. across each resistor (d). power dissipated by each resistor.
Basic Electrical EngineeringDraw symbols of electrical components. Note: You may use both IEC and NEMA symbols. - Conductors crossing but not connected- Conductors crossing and connected - DC source other than battery- DC generator- AC voltage source- Ideal current source- Ideal Voltage Source- Current Controlled Current Source- Current Controlled Voltage Source- Voltage Controlled Current Source - Voltage Controlled Voltage Source
In a series circuit, certain general rules may be stated with regard to quantities of voltage, current, resistance, and power. Express these rules, using your own words: "In a series circuit, voltage..." "In a series circuit, current..." "In a series circuit, resistance..." "In a series circuit, power..." For each of these rules, explain why it is true.
Notes on the verification of ohm's law by voltage method?
Plz what is the methods of this circuit. ALL methods Plz.
Determine V0, I1, ID1, and ID2 for the configuration shown in the figure. With a voltage source (E) equal to 12 volts.