(b)For circuit in Figure Q4(b), given that Z₁1 = 40 , Z₁2 = Z21 = 60,Z22 = 80, Vs = 100 V, R₂ = 20 S,(i)Determine the power absorbed by 10 2 resistor.(ii)If the value of load resistor, R₂ in the circuit in Figure Q4(b) is reduced,justify its effect to the power absorbed by 10 resistor. Show allcalculations.Vs+110Ω 11W+V₁[z]Figure Q4(b)END OF QUESTIONS -1₂+V₂R₂

Answered: Image /qna-images/answer/91544f59-98ac-4e25-81b1-a88cc7a0f78f.jpg

(b) For circuit in Figure Q4(b), given that Z₁₁ = 40N, Z1₁2 = Z21 = 60, Z22 = 802, Vs = 100 V, R₂ = 200, (1) Determine the power absorbed by 10 resistor. (ii) If the value of load resistor, R₁in the circuit in Figure Q4(b) is reduced, justify its effect to the power absorbed by 10 resistor. Show all calculations. Vs (+) 10 Ω 1, W + V₁ [z] Figure Q4(b) 12 + V₂ RL

(b) For circuit in Figure Q4(b), given that Z₁₁ = 40N, Z1₁2 = Z21 = 60, Z22 = 802, Vs = 100 V, R₂ = 200, (1) Determine the power absorbed by 10 resistor. (ii) If the value of load resistor, R₁in the circuit in Figure Q4(b) is reduced, justify its effect to the power absorbed by 10 resistor. Show all calculations. Vs (+) 10 Ω 1, W + V₁ [z] Figure Q4(b) 12 + V₂ RL

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Refer to the circuit on the right. VEB = 0.7 V, when the BE junction is conducting. VECsat = 0.2 V B Vref = 2.2 V (Use two decimal places.) = ∞ VREF IL +5 V R LOAD Figure 2 a. What should be the value of R in ohms if IL is to be maintained at 146 mA under changing load conditions? b. In order to maintain this load current, what should be the maximum allowable load resistance in ohms?
Discuss atleast two basic sources of value for storage technologies in high voltage
B.. What is the load current for the circuit shown in the figure? Please choose one: a. 6.0 mA b. 3.0 mA C. 9.0 mA D. 7.5 mA
Q4/ Assume DC source with internal resistance 7.5 2, connect to load with 8 2 through copper wires with 1mm. What is the length of wire that maximizes the load power? (For copper resistivity = 1.72×102.m).
In the figure is shown a battery having an emf of 12 Volts and an internal resistance of 0.40 Ohm.A resistor R1 of 2.6 Ohms is connected across itsterminals ab. Determine (a) resistance of Rwhich, when connected across terminals ab inparallel with R1 will make the powerdelivered by the battery a maximum; (b)current in R1 and R; (c) terminal voltage ofbattery; (d) power in R1 and in R; (e) power lost in batteryHint: To maximize power in R, use differentiation In the circuit shown, a 6-Ohm resistor connected in series to a parallel combination of tworesistors, one is 30-Ohm and the other is R beingunknown. Determine the value of R if: (a) thepower dissipated in 6-Ohm resistor is equal tothe power in the parallel combination; (b) hepower in 6-Ohm is equal to the power of in R; (c)value of R maximum power transfer.Hint: To maximize power in R, use differentiation
Consider a typical electrical circuit system shown in Figure 2. The circuit consisting of two resisters value R, and R2 (ohm), a capacitance of value C (farad) and an inductance of value L (henry). The input is the supplied voltage V, and the output voltage is Vo- viz R1 Vi R2 Vo Figure 2 (1). Apply Kirchhoffs voltage law or other principles to derive the input-output dynamic model equation. (i). Apply Laplace Transform to determine the model transfer function for the electrical system. (i). Estimate the transfer function for the following R; = (ohm) and R2 = (ohm), L = (henry), and C = (farad) values. Task 4 R, (ohm) R: (ohm) C (farad) (henry) Note: Refer the Table for R1, R2, C and L values. 27 13 24 4 lellll
a) Write the expression for the voltage vC after the switch is closed b) Write the expression for the current iC after the switch is closed. Plot the results of parts (a) and (b).
Two storagebatteries, A and B, are connected in parallel for charging from a d.c. sourcehaving an open-circuit voltage of25V and an internal resistance of 2.5 .The open-circuit voltage of A is 11V and that of B is 11.5 V; the internalresistances are 0.06and 0.05 respectively. Calculate the initial chargingcurrents.
Q6. How potential energy of water is converted into Electrical Energy? Q7. Draw the V-I Characteristic of Solar PV Cell ?
What is the load current for the circuit shown in the figure? Please choose one: a. 9.0 mA b. 7.5 mA c. 3.0 mA D. 6.0 mA
rical Circuits Lab. I and R. Use the term "propórtional" and "inverse proportional ", and X2- Give a definition of ohm's law for the three relationships between V, 4 1- Why dose the I-V characteristics pass through the origin? Discussion: also state the conditions for each individual relationship. tes. 3- Can you obtain practically the current passes through any circuit without using the Ammeter? Explain. 4- What is the difference between (P= I*V) and (P-I * R) ? 5- The circuit shown in Fig (1-5), calculates Requ, Vab12, Psupplied and P. consumed across (R4). RI 6- R1 R28.2 R2 (a) Parallel connection (b) Series connection Fig. (1-3) Resistors connection
4. From the figure shown which is series-parallel, the following values are: ID ohms in series with the parallel combination of 30 and DD ohms respectively. If the supply voltage is bD volts, find the following: a) equivalent resistance b)total current c)individual current d)current at 3D and D ohms only