answer b In your new position at the fluid mechanics laboratory, you are required to do the following:a) Explain the operation and constraints of different viscometers that quantify viscosity influidsb) For water you obtained the following data:Temperature [K] 300310318340Viscosity [cP]0.8509 0.6913 0.5958 0.42What is the viscosity of water at 314 K ?:

Solution: First we need to plot viscosity versus temperature graph as shown below,

Answered: b) For water you obtained the following…

b) For water you obtained the following data: Temperature [K] 300 310 318 340 Viscosity [cP] 0.8509 0.6913 0.5958 | 0.42 What is the viscosity of water at 314 K ?:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ql: The viscosity in industrial measurement continue to use the CGS system of Lunits, since centimeters and grams vield convenient numbers for many fluids. The absolute viscosity () unit is the poise, I poise = 1 gtem. s). The kinematic viscosity (v) unit is the stohes, I stokes = 1 em /s. Water at 20C has u = 001 poise and also V= 0.01 stokes. Express these resalts in (a) SI and (h) BG tanits.
1) At any time, approximately 20 volcanoes are actively erupting on the Earth, and 50–70 volcanoes erupt each year. Over the past 100 years, an average of 850 people have died each year from volcano eruptions. As scientists and engineers study the mechanics of lava flow, accurately predicting the flow rate (velocity) of the lava is critical to saving lives after an eruption. Jeffrey's equation captures the relationship between flow rate and viscosity as: Flow V = Pgt sin(@) 28 сm 10 where p is the density of the lava, g is gravity, t is the flow thickness, a is the slope, and u is the lava viscosity. Typical values are given as follows for the flow rate: u= 4x103 kg/(m.s) ±1% p= 2.5 g/cm³ ±1% t= 28 cm +0.5 cm a= 10° +1 ° g= 9.81 m/s? Determine the likely maximum possible error in the calculated value of the flow rate.
You have been moved into the laboratory for the fluid testing for hydraulic devices, where your job is to illustrate the results of a viscosity test on a Newtonian fluid at various temperatures and explain discrepancies after completing the following given data-sheet in Table A. A considerable amount of research has been carried out in an attempt to understand the exact nature of the temperature variation of viscosity. One relatively simple model assumes that the viscosity obeys an 'Arrhenius-like' equation of the form n = Xe(k)r Хе --------Equation 1 where X = 1.7419 and (E/R) = -0.018 are constants for a given fluid. You are required to carry out appropriate calculations on the effect of changes in temperature given in table A by using equation 1 for Ethanol on the viscosity of a fluid. Table A NO Temperature viscocity n T°C cP 10 3 20 30 40 6. 50 7 60 8. 70 2. 4) 5.
A sliding-plate viscometer is used to measure the viscosity of a Newtonian fluid. A force of 25 N is required to keep the top plate moving at a constant velocity of 5 m/s. what is the viscosity of the fluid? [the unit of the answer must be (N-s/m^2)] 1 attachment 50 cm 25 cm 1 mm fluid stationary plate
7. Aflat thin plate is dragged at a constant velocity of 4 m/s on the top of a 5 mm deep liquid layer of viscosity 20 centipoise. If the area of the plate is 1 m² find the drag force. Assume variation of velocity in the liquid to be linear. [Ans. 16 N]
What should be the surface tension of a liquid if its density, which is 1.44 g/cc, is the same as that of the calibrating liquid? The displacements of the liquid and the calibrating liquid inside the capillary tube are both 0.5 cm. The surface tension of the calibrating liquid is 29.4509 dynes/cm.
A constant volume gas thermometer is used to determine the temperature of an unknown fluid. Pressure data for thermometer in the unknown bath (P) and a Triple Point Cell (P) are given below. P[Torr] 100.0 P [Torr] 127.9 200.0 256.5 300.0 385.8 400.0 516.0 What is the temperature of the unknown fluid bath? explain and show all work please and write clearly
Table 1 shows the variation of dynamic viscosities of water with absolute temperature. Table 1: Dynamic viscosity of water with absolute temperature. Viscosity µ, Pa.s x 10-³ 1.787 Temperature, K 273.15 278.15 283.15 293.15 303.15 1 313.15 333.15 353.15 373.15 4G 1.519 1.307 1.002 0.7975 0.6529 0.4665 0.3547 0.2828 a) Using excel software, develop a relationship of for viscosity in the form of μ=A+BT+CT² + DT³ + ET. Done Show your trend line regression and standard deviation for linear and polynomial index (quadratic T², cubic T³ and T). b) Using the relationship developed, predict the dynamic viscosity of water at 50 °C at which the reported value is 5.468 x 10 Pa.s. Compare your result with the results of Andrade's equation which is given in the form of μ = D.e BT where D and B are constants whose values are to be determined using viscosity data given.
. I am planning to perform some volume-flow rate measurements in the Fluid Mechanics Laboratory. For this, I need a volumetric measuring tank (graduated cylinder) and a stopwatch. I considered the volume of the measured tank as 15 gallons and a stopwatch with reaction time as 1/10th of a second (though resolution of 1/1000th of a second). What is the volume flow rate if it takes 5 minutes to fill a 15-gallon of tank? Determine the smallest division to be on the tank in order to estimate the volume flow rate within an accuracy of ± 0.05 gpm.
Check the following equation for dimensional homogeneity: mv = = 1.5² (Fcose) dt where m is mass, v is velocity, F is force, is an angle, and t is time. Check that each term in the equation has the following dimensions: [MªLbTC] where you are to choose the coefficients a, b, c. Answers: a = i b = i C=
Estimate the Celsius equivalent of Absolute temperature (a) and standard Temperature (b). 19 put of BI三|に Paragraph question Path: p Maximum file size: 100MB, maximum number of files: 1 hp
Fluid mechanics [Dimensional Analysis] A breakwater along a river measures 1.5 m by 4.0 m. A model is built to a scale of 1:15. The model is tested in a laboratory with a velocity of 0.80 m/s and the force acting on the model is measured to be 5.0 N. Determine (a) the velocity and (b) the force on the prototype. Find the: a. velocity =___________m/s b. force =___________kN