B: The pump in Fig. Q3B increases the pressure in the water from 200 to 4000 kPa with a flow rate of 0.1 m³/s? The electric power of motor 275 kW. Determine the mechanical efficiency of the pump and overall efficiency pump/motor unit when the motor efficiency is 90 percent. Fig. Q3B 50 mm Pump 100 mm € Water Motor

B: The pump in Fig. Q3B increases the pressure in the water from 200 to 4000 kPa with a flow rate of 0.1 m³/s? The electric power of motor 275 kW. Determine the mechanical efficiency of the pump and overall efficiency pump/motor unit when the motor efficiency is 90 percent. Fig. Q3B 50 mm Pump 100 mm € Water Motor

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A DC driven pump running at 100 rpm delivers 30 litres per second of water at 40°C against a total pumping head of 27 m with a pump efficiency of 60%. Barometer pressure is 758 mmHg. What pump speed and capacity, would result if pump rpm were increase to produce a pumping head of 36 m assuming no change in efficiency. 2. Pump digghange 20 T d is 1C00
2. A pump draws water from a lake delivered to a height of 50 meters above the lake and encounters 15 meters of headloss. Determine the pump power requirement in Kilo-Watts to deliver a constant supply of 500 Liters per second? The correct answer has a margin of 1 from exact answer. Velocity head is neglected.
A pump rated at 65% efficiency is used to transport water from a large open reservoir to a point 10m above at a rate of 450 L/min, into a vented tank. Assuming friction is negligible and that the efficiency of the motor is 77%, how much electricity is required to keep the process running for 24 hours? Choices: A. 29.37 kWh B. 35.28 kWh C. 56.71 kWh D. 43.21 kWh
6. A pump is delivering water from the surface of a lake to a tank 20m above at a rate of 70L/s while the pump label suggests it consumes 18kW of electric power. If all the loses and any changes of kinetic energy are negligible, a. What is the pump efficiency? b. What is the pressure rise of water in the pump?
Q1: Find the pump efficiency if the pressure difference across the pump is 230 kPa. If the outlet 2₁ 14 cm Z2 diameter of the pump is 7 cm, the inlet diameter is twice the outlet diameter. take the mass flow = 50 rate of the pump is equal to 50 kg/s 72. 1 Wate C the pump nmotor = 85 % Motor 20 W
A 20-KW motor with 80% efficiency drives a centrifugal pump delivery 0.08m3/sec against a head of 20m. Determine the pump efficiency
What size pump is needed to supply 10 gpm to a cylinder when the electric motor is rotating at 1725 rpm? Assume 100% efficiency and state your answer in in3/rev to two decimal places.?
Q3- A centrifugal pump draws water from a sump through a vertical 15 cm pipe diameter. The pump has a horizontal discharge pipe 10 cm diameter which is 3.5 m above water level in the sump. While pumping 30 l/s, gages near the pump at entrance and discharge read -35 kPa and+180 kPa respectively. The discharge gauge is 0.5 m above the suction gauge. Determine the power output of the pump. * P 10.5 m 3.5 m
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate: a) the pump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
A centrifugal pump delivers 60 litres of water per second to a tank situated at a height of 20 metres. If the overall efficieney of the pump is 70%, find the power required for the pump. (Ans. 16-8 kW) 1.
A fan can deliver a total pressure of 117 mm of water gage. The boiler requirement is 45,509 m^3/hr of standard air and the mechanical efficiency is 76 %. Use the total head in terms of air. Determine the size of the driving motor in kW Answer in whole number
A hydraulic vane pump running at 1800 rpm develops 2 L/s flow at 750 kPa. Volumetric efficiency is .85 and overall efficiency is 0.8. Determine the Theoretical Torque required, TT (N-m). (Hint: first calculate the mechanical efficiency and theoretical flow rate. Convert rpm to rad/s). O 9.41 N-m 8.85 N-m 9.35 N-m 9.62 N-m 8.80 N-m