Beam AB is made of three plates glued together and is subjected, in its plane of symmetry, to the loadingshown. Knowing that the shear force is V=3.5kN and I=8.63*106 m“, determine the following:-100 mm20 mm-Joint a80 mmC20 mm -68.3 mm20 mm60 mmThe value of Q is equal to in m3:The value of t for the Joint a is equal to in mm:The average shearing stress at Joint a is equal to in kPa:

V = 3.5 KN = 3.5 ×10³ N I = 8.63 × 10-6 m4 Solution attached below

Beam AB is made of three plates glued together and is subjected, in its plane of symmetry, to the loading shown. Knowing that the shear force is V=3.5kN and I=8.63*10® m*, determine the following: 100 mm 20 mm - Joint a 80 mm 20 mm 68.3 mm 20 mm 60 mm The value of Q is equal to in m³: The value of t for the Joint a is equal to in mm: The average shearing stress at Joint a is equal to in kPa:

Beam AB is made of three plates glued together and is subjected, in its plane of symmetry, to the loading shown. Knowing that the shear force is V=3.5kN and I=8.6310® m, determine the following: 100 mm 20 mm - Joint a 80 mm 20 mm 68.3 mm 20 mm 60 mm The value of Q is equal to in m³: The value of t for the Joint a is equal to in mm: The average shearing stress at Joint a is equal to in kPa:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2
Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1600 mm?. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 т 10 m 10 m K 6 т G H 6 m 15° 15° 40 kN 50 kN E F 6 т б т А B
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the loadP = 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa C. Aluminum L=2m A=500mm2 2m 2m E-72Mра P=20KN
The rigid bar BDE is supported by two rods AB and CD. Rod AB is made of aluminum (Eal = 70 GPa) and has a cross-sectional area of AAB= 400 mm2; Rod CD is made of steel (Esteel = 200 GPa) and has a cross-sectional area of ACD = 500 mm2. The load P = 31 kN is applied at point E as shown in the figure. [LAB = 0.3 m, LCD = 0.4 m, a = 0.2 m, b = 0.4 m] Determine the internal force of rod AB?KN Determine the displacement of point B?in mm Determine the displacement of point E?
8.10 This is steel, consisting of 9 rods that are articulated together in the nodes. There is a fixed bearing in A and a roller bearing in B. The steel is loaded with a point load, P, in the middle. The maximum permissible normal stress is oy = 200 MPa. Cross section: s9 S8 54 53 55 s1 S7 d = 40 mm S2 S6 1m 1m 1 m 1 m a) Calculate the rod forces. Express the answers with P, and state whether they are stretched or pressed. Is there any zero spells? b) Determine how large the load P can be without material breakage or buckling the spells. 3 m
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. BRONZE L-5 m A 500 mm E-80 GPa STEEL L-4 m A-400 mm E-200 GPa 3 m. 5 m. VP
QUESTION 2 A steel cantilever beam is made of two structural tee- section beams welded together as shown in the Figure 2 below. Determine the allowable safe load (P) that the beam can carry. The allowable stresses are: 0-150MPa in tension and compression, T=100MPa in shear, and q=2000N/mm on the welded joint. 150 -200mm- -150- 25 weld 25 ΝΑ 25 M=P V=P -1.0m- Figure 2 weld 0.5m 31
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. 2.0 m | P₁ = 45 KN W₁ = 44.24 kN/m 3.0 m a. b. 3-200 6-200 350mm by 400mm f'c-35 MPa fy=415 MP.. Ps= 10 mm conc. cover= 40mm 250mm by 400mm f'c-21 MPa fy=415 MPa Ps= 10 mm conc. cover= 40mm
A two pinned end bars AB (copper) and BC (aluminum) is subjected to a horizontal force P = 90KN applied at pin B %3D as shown in the figure, determine the horizontal displacement of pin B. Aluminum: L= 1.5m, A= 1000mm2, E= 70 GPa Copper: L= 2.0m, A= 850mm², E= 120 GPa Degree: 45° Alumaum L-15m A=1000 mm E-70 GPa >P=90 kN Copper L=2.0m Aa550 mm E=120 GPa
Calculate the force in member GL in kN LE in kN KE in kN KL in kN DE in kN If the force is tensile, answer in positive value. Otherwise if it is compressive, answer in negative value.
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa Aluminum L=2m A=500mm 2m 2m E-72Mра P=20KN
The rigid bar AB, attached to two vertical rods as shown is horizontal before the load P=50kN is applied. • Determine the deformation of aluminum in mm. • Determine the deformation of steel in mm • Determine the vertical movement of P in mm