Before energizing the motor of a drill press, always ensure that the: (A Chuck key is placed in the chuck Shank drill bit is placed in the spindle Chuck key is removed from the chuck Shank drill bit is removed from the spindle

Q: A 5.0V stabilised power supply is required to be produced from a 12V DC power supply input source. T...

A:

Q: Q3/ The three forces and the couple are applied to the bracket shown in Figure below. Determine (1) ...

A: Given  

Q: 5. While the pressure remains constant at 689.5 kPa the volume of a system of air changes from 0.567...

A: As per guidelines we need to answer only first 3 subparts of questions so please repost rest questio...

Q: When assembling refrigerant lines on the job, the tubing should be kept _______. Select the answer ...

A: Given  When assembling refrigerant lines on the job, the tubing should be kept _______.

Q: Q2/ For the force (F), the rectangular components are Fx = -40 N, and Fy = 60 N, %3D respectively. D...

A: Given data Fx = -40 N Fy = 60 N   Fx and Fy are rectangular components 

Q: As the 39500-lb airplane takes off, the tangential component of force exerted on it by its engines i...

A: Given:mass of the airplane, m=39500 lbtangential component of force, Ft=53000 lbacceleration due to ...

Q: 2. A ball is dropped vertically onto a 30° incline at A, the direction of rebounds forms an angle of...

A: The given projectile motion is given as shown below. Considering the motion of the stone along the ...

Q: When a 10N mass is hung on a spring, it stretches .25m. 1. What is the spring constant? 2. How much ...

A: Given, Force F1 = 10 N Extension of spring under force F1 = x1 = 0.25 m Force F2 = 20 N   For spring...

Q: A solid rectangular parallelepiped is made of aluminum and is initially at 20 C. The base is a 2 cm ...

A: The heat transfer in straightforward calculations (for example plane pieces, chambers and circles), ...

Q: For the given data shown. the value * :A1 is 200 mm 30 m A1 Neutral Ais NA 0 mm A2 Relerence Line 40...

A:

Q: 4. A pulley has a constant angular acceleration of 5 rad/sec?. When the angular velocity is 4 rad/se...

A: Givenα=5 rad/s2ω=4 rad/sa=8ft/s2

Q: 0.016 kg Average mass of one clamp, m. Balancing position (center of gravity) of meterstick, x 0.497...

A:

Q: 1.14 In the hoist drive system shown in Fig.22 , the mass M is considered being moved upwards with n...

A:

Q: 3 m find the Velocity at point B 2 m • 30 3 rad/s

A: We will answer the first question since the exact one was not specified. Please resubmit the questio...

Q: A fold-down shelf opens up and is supported by a rope attached between points A and B. What is the t...

A: GivenW=57lbfind tension FAB in the rope 

Q: Which is the higher Moment of Inertia * :of these cross sections Cross section 1 Cross section 2 Cro...

A: The moment of Inertia of a plane area with respect to x and y axis respectively is defined by the in...

Q: A pipeline 0.5 m diameter and 1200 m long is used for transporting an oil of density 150 kg/m3 and o...

A: Write the given data.  d=0.5 m L=1200 m ρ=150 kg/m3Q=0.4 m3/s μ=0.91 Pa·s Here, d is the pipe diamet...

Q: Q1/The acceleration is defined by the relation a=(8-0.6 v). Knowing that the initial velocity is 14 ...

A:

Q: Q3/ The three forces and the couple are applied to the bracket shown in Figure below. Determine (1) ...

A: (1) Apply force equilibrium in horizontal direction to write the resultant in horizontal direction. ...

Q: Calculate the maximum diameter (mm) of a steel ball that would float on water at 15°C. At 15°C, σ = ...

A:

Q: An air curtain is produced by blowing air through a long rectangular nozzle at high air velocities a...

A:

Q: Two blocks are being pushed along an incline. Block A weighs 7.00 kg and block B weighs 14.00 kg. Th...

A:

Q: Q4/B/ the value of X-bar is: * Q4/C/ The value of Y-bar is:

A:

Q: 11. The work required to compress a gas reversibly accord- ing to pV1.30 = C is 67,790 J, if there i...

A:

Q: The three beams in the figure have thesame loading. However, one has a moment releasejust to the lef...

A:

Q: If the surface tension of water-air interface is 0.073 N/m, the gauge pressure inside a rain drop of...

A: From the given question, Surface tension of water-air interface = σ = 0.073 N/m Diameter of the rain...

Q: Calculate the amount of air in kg necessary for combustion of 1 kg of octane (C8H18) with 30 % exces...

A: Calculate the amount of air in kg necessary for combustion of 1 kg of octane (C8H18) with 30 % exces...

Q: Q4/ For the figure below, all dimensions in inch. A/The total Area: 1.5 2.5 2.5 2.5 2.5 Q4/B/ the va...

A:

Q: the relation a=(8-0.6 v). Knowing that the initial velocity is 14 m/s. A/ the velocity at t= 4 s: * ...

A:

Q: Q4/B/ the value of X-bai Q4/ For the figure below, all 0.987 dimensions in inch. A/The total O 2.5 A...

A:

Q: @Collors A G B con woue freely aicng ir repeetive quide bars. At the ornent own, sie = 3/5,sin -4/5 ...

A: Solution: Given Data: α=sin-135=36.9oβ=sin-145=53.1ovB=1 m/s    down

Q: Eonsider a osow botshat stagitupward fom the grund y-0) at ime t=0 wih niha elocy, -4 – Take g= 98- ...

A:

Q: *8-12. A pressure-vessel head is fabricated by gluing the circular plate to the end of the vessel as...

A: Given Internal pressure = 450 MPa To find Average shear stress in the glue Wall stress

Q: Two bars are used to support a load. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ring...

A:

Q: is represent the relationship between temperature and time O phase diagram O system O cooling curve ...

A:

Q: Two sections of steel drill pipe, joined bybolted flange plates at B, are subjected to a concentrate...

A: Calculate the total load due to the uniformly distributed torque on the part BC in the pipe. T0=50 k...

Q: What is the Compressible Bernoulli Equation about?

A: Given Compressible Bernoulli Equation To find Notes about compressible Bernoulli Equation

Q: A steel beam ABC is simply supported at Aand B and has an overhang BC of length L =150 mm(see figure...

A: Given: To determine: a) Disregarding the weight of the beam, the required width b of the rectangula...

Q: 32. A bare fuel rod has a diameter of 0.373 in and length of 12 ft. The volumetric heat generation r...

A:

Q: Given a system as shown in the following figure. Calculate the water level difference between two ta...

A: Given data as per question p1=7.35 psi=50676.47 pap2=0.5 atm=50662.5 paz1=?z2=0Q=1 m3h =13600 m3sAss...

Q: 4) A simple vapour compression system keeping the evaporator temperature of 8'C and condensing tempe...

A:

Q: value of logarithimic decrement ?

A: Given: A vibratory system consists of a mass,m=12.5 kgSpring stiffness,k=1000 N/mDashpot damping coe...

Q: the current (in A) required

A: Given: An electromechanical is to be used to cut through hole into ,Thickness,t=12 mmThe hole has a ...

Q: By Mechanics of meteriels -CoN cept of strain Prove 4hat G 2(1+v) - modulus of frigidity E = modulus...

A:

Q: In a steady-state operating power plant, saturated liquid H2O at 122 deg C is fed to a boiler at 3.7...

A: It is asked to find the temperature of the water coming into the boiler Mass flow rate, m = 2.5 kg/s...

Q: The structure consisting of three elements is connected at A, B and C by pins. Assume that at point ...

A:

Q: *2-96. The tower is held in place by three cables. If the force of each cable acting on the tower is...

A:

Q: In most of internal combustion engines, crankshaft bearing is  Select the correct answer below: A....

A: Concept: Hydrodynamic bearing: 1) In this bearing, two rubbing surfaces of bearing are separated by ...

Q: Define the equations necessary to find the behavior of the mechanism (reduced to their maximum expre...

A:

Q: normal force (in N) at Q is,

A: Given: From the given figure:Block P of mass 2 kg slides down the surface and has a speed 20 m/sat t...

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.