Your trusty lab assistant Juniper the Husky accompanied you to the park to review some data in the sun. While you studied the results of the litter decomposition experiment you just completed, Juniper explored potential soil sampling sites by running through mud puddles. Just as you finished your calculations. Juniper ran across your notebook, getting mud all over the results. The three rate constants you calculated (0.63, 0.45, and 0.82 y) are still readable, but you can't tell which litter types they go with. You are not concerned, because you understand the underlying scientific principles. Match the rate constants above to the appropriate litter type below. Provide your rationale. Litter Total C (%) Total N (%) Lignin (X) Cellulose (%) k(y) Red alder 45 1.5 20 25 Douglas-fir 45 0.9 18 24 Western 23 48 0.6 24 hemlock

Your trusty lab assistant Juniper the Husky accompanied you to the park to review some data in the sun. While you studied the results of the litter decomposition experiment you just completed, Juniper explored potential soil sampling sites by running through mud puddles. Just as you finished your calculations. Juniper ran across your notebook, getting mud all over the results. The three rate constants you calculated (0.63, 0.45, and 0.82 y) are still readable, but you can't tell which litter types they go with. You are not concerned, because you understand the underlying scientific principles. Match the rate constants above to the appropriate litter type below. Provide your rationale. Litter Total C (%) Total N (%) Lignin (X) Cellulose (%) k(y) Red alder 45 1.5 20 25 Douglas-fir 45 0.9 18 24 Western 23 48 0.6 24 hemlock

Human Anatomy & Physiology (11th Edition)

11th Edition

ISBN:9780134580999

Author:Elaine N. Marieb, Katja N. Hoehn

Publisher:Elaine N. Marieb, Katja N. Hoehn

Chapter1: The Human Body: An Orientation

Section: Chapter Questions

Problem 1RQ: The correct sequence of levels forming the structural hierarchy is A. (a) organ, organ system,...

See similar textbooks

Similar questions

Imagine you are conducting an Ames test experiment. Based off your results (shown in pictures), answer these questions: 1. Generate a fully labeled graph/figure depicting the data generated in lab (minimally you should include the data from control, 2-NF, and two different test compounds.) 2. Make a bulleted list of 3 distinct and specific observations/patterns seen in your graph/figure - for each observation, indicate specifically where you should look to find the observation on your figure. 3. Write a 5 sentence minimum explanation of the results (i.e., a discussion of the hypothesis, the experimental prediction and the conclusions based on your observations from experimental data)
In UV/Visible spectrophotometer analysis for a multicomponent system, there are only two dyes used in the mixture, the two proportions should be totalled to 1.0. but on finding You got 0.6 in total. Explain the reasons for the difference.
The replicate results (mg/L) obtained from calcium determination of a blood sample using atomic absorption spectrophotometry (AAS) and a new colorimetric method were as following: AAS : 11.2, 11.2, 10.6, 11.2, 9.7 and 10.0 Colorimetric : 9.2, 10.5, 9.7, 11.5, 11.6, 9.3, 10.1 and 11.2 Determine whether the mean of both methods have a significant difference at 95% confidence level.
A mixture of species of A and B is injected into a liquid chromatographic column with length of 20.0 cm. The obtained separation results are listed as follows: Species Retention time (min) Peak Width at Base (min) Non-retained 3.0 A 5.2 0.48 В 5.9 0.56 From the data, the calculated resolution Rs is smaller than 1.5 for A and B when the column length is 20.0 cm, which indicates that A and B are not separate completely. What is the new column length (unit: cm) necessary to separate the A and B species with a good resolution Rs = 1.5? Please keep your answer to one decimal place.
(b) Table Q1 below provides optical measurements of samples with known concentrations of analyte (ten samples were measured and the average and standard deviation are presented). They are also represented graphically in Figure Q1, below the table. Analyte concentration (nM) 0.1 0.2 0.5 1 2 5 10 15 fluorescence intensity 300000 250000 200000 150000 100000 50000 0 0 Table Q1 Fluorescence intensity (average) 9300 9200 10800 19600 37200 90000 178000 224000 5 [Analyte]/nM 10 Standard deviation 2000 1200 1000 2000 10000 30000 25000 40000 15 Figure Q1. Signal intensity for different analyte concentrations. Error bars are standard deviation. (ii) Calculate the limit of detection (LOD) for this sensor. (iii) A patient sample measured using this biosensor in the diagnostic laboratory generates a signal of 142800. The coefficient of variation of the device is 5%. Explain whether the diagnostic lab would have the confidence to report that the sample has a concentration in analyte of 8 nM or…
I need assistance with how to read Fletcher Munson graphs. Please help and show me the proper way to analyze these graphs. The previous experts I've asked on this platform were incorrect.
The following image is a scheme for serial dilutions prepared for spectrophotometric analysis. If the stock solution concentration is 0.05 % (v/v) can you calculate the other tube’s concentrations in % v/v? I've used this with direct dilutions, how would I use this on serial dilutions?
Suppose your professor handed you a bottle of kombucha with 2.0 ml in it and told you to make a 10^-2 dilution of the entire culture. Explain how you would do this. Show your calculations.
What is the DNA concentration (ug/ml) of an undiluted sample with A260 reading without background of 0.5 ?
A 25.0 mL aliquot was taken from a 500.0 mL sample of tonic water containing an unknown amount of quinine and diluted to a volume of 150.0 mL. At 347.5 nm, the fluorescence intensity of the diluted sample was measured as 89.3 on an arbitrary scale. Under similar conditions, a 25.0 ppm standard quinine solution had a fluorescence intensity of 173. Calculate the mass of quinine in the original tonic water sample. mass: mg * TOOLS x10
A flat (not spherical) tissue engineered skin (thickness 3.9 mm) is attached to the bottom of a dish and cultured with cell media atop it (which has an oxygen concentration of 0.15 mol/m3). The diffusivity of oxygen in the skin is 3.2 E-9 m?/s, and according to experiments that you've performed, you want to make sure that the concentration of oxygen in the device doesn't fall below 0.06 mol/m3. (Below that concentration harms the cells.) The rate of oxygen consumption is -5 E-17 mol/[cell•s]. What is the maximum cellularity (in cells/mL, three significant digits) that this tissue engineered skin can support?
A 10 μL-aliquot of a resuspended genomic DNA stock solution was obtained and further diluted by adding 990 μL TE buffer. The A260 of the resulting solution was 0.316. Determine its concentration in µg/µL.