Calculate the actual sag and vertical sag from the following information Weight of conductor = 0.9 kg / m Cross-sectional area of conductor = 125 mm^2 ice coating=12mm redial Ice density=915 kg/m^3 Intensity of wind pressure=50 kg/m^2 on project area Breaking strength of material of conductor = 42 kg /mm^2 Factor of safety = 2.5 Span = 260 m

Calculate the actual sag and vertical sag from the following information Weight of conductor = 0.9 kg / m Cross-sectional area of conductor = 125 mm^2 ice coating=12mm redial Ice density=915 kg/m^3 Intensity of wind pressure=50 kg/m^2 on project area Breaking strength of material of conductor = 42 kg /mm^2 Factor of safety = 2.5 Span = 260 m

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.1P: The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C...

See similar textbooks

Similar questions

12. There are 6 conductors in a double circuit line. Each conductor has a radius of 12 mm. The 6conductors are arranged horizontally. The center to center distance between the conductor is 2m. The sequence of conductors are from left to right as follows: a,b.c,a', b', c'. Calculate the inductance per km per phase of system. the a' 2 m 2 m 2 m 2 m 2 m
The emf induced in a conductor when placed in magnetic field can be determined by the Lenz's law True False
Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material consists of two layers. The thickness of each layer is 2 cm. The voltage of first and second layers are 20 kV, 5 kV respectively. The maximum Electric stress of the cable is
Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material consists of two layers. The thickness of each layer is 2 cm. The voltage of first and second layers are 20 kV, 5 kV respectively. The minimum Electric stress of the cable is * 9.45 kV/cm 1.89 kV /cm O 1.25 kV/cm 5.78 kV/cm Non of them
Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material consists of two layers. The thickness of each layer is 2 cm. The voltage of first and second layers are 20 kV, 5 kV respectively. The minimum Electric stress of the cable is
temperature rating that a conductor must have and still have 69 Ambient Tempere 4. The ampacity of 15 current-carrying 10 RHW aluminum conduc- tors in a raceway in an ambient temperature of 75'F is 1. gon factor for conductor ampacity in this location is (a) 12A (b) 15A (c) 22A (d) 30A 0.71 b0.82 0.88 0.96 5. Ain) uous load if the ambient temperature is 75°F and there are nine THHN conductor is required for a 19.70A noncontin- ne ambient temperature is 71"C, the minimum insulation current-carrying conductors in the raceway in a dry location. he capacity to carry current is (a) 14 (b) 12 (c) 10 A 60°C AI 90°C 105°C (d) 8 0 120°C 6. 6.11 Ampacity Adjustment [310.15(B)(3)(a)] The ampacity for each of nine current-carrying 10 THW conduc- tors installed in a 20 in. long raceway is 1 The ampacity of six current-carrying 4/0 XHHW aluminum con- ductors installed in a ground floor slab (wet location) is (a) 25A (b) 30A (c) 35A (d) 40A a) 135A 0) 144A (e) 185A 4 210A
The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C and a 60-Hz resistance of 0.0956 ohm per mile at 50C for the all-aluminum Marigold conductor, which has 61 strands and whose size is 1113 kcmil. Assuming an increase in resistance of 2 for spiraling, calculate and verify the dc resistance. Then calculate the dc resistance at 50C, and determine the percentage increase due to skin effect.
The figure shows a conductor with four strands. Compute the GMR in terms of the radius r. Round-off your answer to 3 decimal places. Answer:
Correct statement related to weight of conductor and sag is .............................. Weight of conductor ∝ √(sag) Weight of conductor ∝ (1/sag) Weight of conductor ∝ (sag)^3 Weight of conductor ∝ sag
Each conductor of a 3-0 overhead line is suspended from a cross arm of a steel tower by a string of 4 suspension insulators. The voltage across the third 33 kV. The shunt capacitance between each insulator and the earth is 1/8th of the capacitance of the insulator itself. Find the voltage across string and string efficiency. D-128 Lod Fa
estion The magnetic field inside cylindrical conductor zero directly proportional to p inversely proportional to p o inversely proportional to p2
33 kv single core cable has a radius of conductor of 0.6 cm. The insulation martial has two layers. The thickness of the first and second layers are 0.8 cm and 0.4 cm respectively. The relative permittivity of the first and second layers are 4 and 3 respectively. Find 3- The minimum electric stress of the second layer. 4- The minimum electric stress of the first layer.