Calculate the allowable force in rod (1). Answer: F1- i N Attempts: 0 of 1 used Submin Save for Later Part 2 The parts of this question must be completed in order. This part will be available when you complete the part above. Part 3 The parts of this question must be completed in order. This part will be available when you complete the part above.

Calculate the allowable force in rod (1). Answer: F1- i N Attempts: 0 of 1 used Submin Save for Later Part 2 The parts of this question must be completed in order. This part will be available when you complete the part above. Part 3 The parts of this question must be completed in order. This part will be available when you complete the part above.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem (1) Three steel rods (E = 200 GPa) supports a 50 kN load P. Each of the rods AB and CD has a 300 mm? cross-sectional area and rod EF has a 600 mm? 500 mm cross-sectional area. В (a) statically determinate or indeterminate. Why? (b) stress in each rod. State whether the structure is E 400 mm Determine the force and the OF Determine the deformation of each rod. (c) Note: The link BED is rigid, and BE = ED.
Q.2) A rigid bar ACD is supported by two circular steel (E= 30x10° psi) rods AB & DE and a pin support at C. Bar ACD was horizontal prior to the application of load P. The tensile strain measured in rod AB after the application of the load is ɛ1= 0.003. Determine the rotation 0 of the bar ACD and the normal strain in rod DE. Also calculate the value of load P for these deformations. The diameters of rod AB and DE are 1.5 in. and 2 in, respectively. P - 4 ft 4 ft- 6 ft A Rigid (2) 6 ft 8 ft (1) E В
A magnesium-alloy rod (E = 6.5 x 10 ksi) of Prob. 3.4-6. diameter d 1 in. is encased by a brass tube (E 15 x 10 ksi) with outer diameter d. = 1.5 in.; both have length. L = 20 in. An axial load P = 10 kips is applied to the resulting bimetallic rod. (a) Determine the normal stresses and , in each material, assuming that the magnesium rod and brass tube are securely bonded to each other. (b) Determine the elongation of the bimetallic rod. P
The thin rectangular plate is uniformly deformed such that Ex = 220E, Ey= -680 uE, and yy = 870 urad. If a = 35 mm, determine (a) the normal strain &, in the plate. (b) the normal strain &, in the plate. (c) the shear strain ynt in the plate. B D. a a a a a a a a a Answers: (a) En= i HE (b) Et= i HE (c) Ynt = i prad
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that di =50 mm and d2 =30 mm, find the average normal stress at the midsection of (a) rod AB (b) rod BC A 300 mm -d, В 5OKN 150 mm 30KN
Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
Question # 4: Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. ( 2 m a 0.5m 400 KN 100 mm 300 mm 100 mm Section a-a
A steel tube is rigidly attached between an Al rod and a bronze rod. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress of 80MPa in Al, 150MPa in steel and 100 Mpa in bronze. -1.0m 200 mm² 2.0m Steel 400 mm² 2P -2.5 m Bronze 500 mm²
Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. 4 m a -1 m 100 KN 250 mm 1 600 mm 200 mm Section a-a
The wire BC has a diameter of 0.175 in. and the material has the stress-strain characteristics shown in the figure. Determine the vertical displacement of the handle at D if the pull at the grip is slowly increased and reaches a magnitude of (a) P= 480lb, (b) P= 700lb. Assume the bar is rigid.
The copper rod AB and steel rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T1 = 17°C, determine the average normal stress in each member when T2 = 47°C. Also, how far will the collar be displaced? The cross-sectional area of each member is 1130 mm?. %3D Сopper Steel Elastic Modulus (GPa) 120 200 Coefficient of thermal expansion (1/°C) 17x10-6 12x10-6 В 1 m 0.6 m-
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 2.2 in.². Assume a = 4.00 ft and b = 4.80 ft. If the normal stress in each member must not exceed 45 ksi, determine the maximum load Pmax that may be supported by the structure. A Answer: Pmax b B E b kips