Calculate the normal stresses (in Pa) at point Bof the bracket caused by the 23010N force.
Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11633 N force. - 540…
A: P= 11633 N Width of the cross section, b= 60 mm Height of the cross section, h= 180 mm
Q: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected…
A:
Q: A steel tube of 200 mm external diameter is to be shrunk onto another steel tube of 60 mm internal…
A: For inner tube: Write the expressions for A and B for thick cylinder. At r=0.030,…
Q: A steel tube of 300 mm external diameter is to be shrunk on to another steel tube of 90 mm internal…
A: Given data: External diameter, d3 = 300 mm, r3 = 150 mm Internal diameter, d1 = 90 mm, r1 = 45 mm…
Q: The state of stress at a point is given by ox = -6 MPa, ơy = 4 MPa, and Txy = -8 MPa. The maximum…
A:
Q: b) For the thin walled pressure vessel subjected to an internal pressure of 150 psi and as shown…
A: Given data: - The pressure inside vessel is P = 150 psi. The length of the vessel is L ft. The…
Q: Find the principle stresses at A and maximum shear stress.
A:
Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11023N force. E4.png…
A:
Q: A: Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at a…
A: Dear student, According to the guidelines I am allowed to answer only one…
Q: Find normal and shearing stresses at point A .
A: For the Normal Stress at pt.A (considering the maximum stress condition) Normal Stress, σx = PA…
Q: b) For the thin walled pressure vessel subjected to an internal pressure of 150 psi and as shown…
A: Given Data Internal pressure of vessel is: P=150 psi The length of the vessel is : L ft Thickness…
Q: Thickness = 15 mm Find the stresses developed at point A 100 mm A ta 70 mm 180 mm 30 50 mm 500 N
A: Given: The thickness, t = 15 mm The width, b = 70 mm
Q: stress in the segment QR
A: Given; A bar having cross-sectional area(A)=700 mm2Various loads at the positions indicated at the…
Q: Compute the stress in a round bar subjected to a direct tensile force of 3200 N if the diameter of…
A: Given data: F=3200 Nd=10 mm Need to determine the stress in a round bar.
Q: A pipe has an outside diameter of 0.8 inches and inside diameter of 0.19 inches. A force of 105 lbs…
A: Given Outside diameter, d2 = 0.8 in Inside diameter, d2 = 0.19 in…
Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11023 N force.
A: The stress due to normal force on the beam can be determined as,
Q: 3. For the state of stress shown below, calculate the principal stresses and maximum shear stress.
A: σx = 90 Mpa σy = -60 Mpa Txy = 20 Mpa
Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb.…
A:
Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11023 N force. E4.png…
A:
Q: . Find the thickness of the flat end cover plates for a 1 N/mm2 boiler that has a diameter of 600…
A:
Q: A rod (ABC) diameter at AB is 30 mm and diameter at BC 10 mm is subjected to a tension load of 40…
A:
Q: A state of stress at a point A is given by ox = 210 MPa, oy = -140 MPa, and txy = 95 MPa. Which of…
A: The correct answer is option e) 234.071 Mpa
Q: 1 MPa 2- For the state of stress as shown below 2 MPa a) Find principal stresses З МРа b) Draw…
A: Given:σx=3 MPaσy=1 MPaζxy=2 MPa
Q: Calculate the normal stresses (in Pa) at point Bof the bracket caused by the 23010N force. E4.png -…
A:
Q: b) For the thin walled pressure vessel subjected to an internal pressure of 150 psi and as shown…
A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…
Q: For the thin-walled pressure vessel subjected to an internal pressure of 150 psi and as shown below,…
A: The stress that acts in parallel direction with the longitudinal axis is called longitudinal stress…
Q: A load of 7,000 N acts on the machine part shown in Fig. 5a. The machine par thickness of 15 mm…
A:
Q: Oy = 90MPA %3D Try 60MPA %3D Ox=20MPA
A: Given Data Normal stresses σx= 20MPa σy=90MPa Shear stress fxy=60MPa Main stresses are the…
Q: A state of stress at a point A is given by ox 210 MPa, oy = -140 MPa, and txy = 95 MPa. What is the…
A: Given, σx=210 MPaσy=-140 MPaτxy=95 MPa
Q: For the figure shown below. Calculate the increase in vertical stresses (Ac) at point A at depth of…
A:
Q: Compute the normal and shear stress on a plane which is 45° inclined from vertical axis of a…
A: Given data: - The angle of the plane with vertical axis is θ = 45o. The axial stress on the box is…
Q: b) For the thin walled pressure vessel subjected to an internal pressure of 150 psi and as shown…
A: Given data: - The pressure inside vessel is P = 150 psi. The length of the vessel is L ft. The…
Q: is shown below, 400 300 200 100 Stress (MPa)
A: 1.Modulus of elasticity can be obtained by taking the slope of stress-strain curve in elstic…
Q: Find the principal normal stresses and their directions that will occur in case of stress in the…
A:
Q: The state of stress at a point in a component is ox = -14 ksi, oy = -20 ksi, Ty -4 ksi. Sketch the…
A:
Q: Q- Compute the tensile and compression stresses for below 40 KN 120 24 KN/m C B D 2m A NA mm 5m 3m…
A:
Q: Find AT for which the stresses in PE and E 29 x 10 nri for sta
A: Given: E=29×106 psiα=6.5×10-6 /FStress in two rods are sameTo determinechange in temperature
Q: 10 0M, -FXED SUPPORT Find the principal stresses and maximum in-plane shear stress at element A.…
A:
Q: A state of stress at a point A is given by ax = 29 MPa, oy =- 195 MPa, and txy = -3.751 Which of the…
A: Data given- σx = 29 MPa σy = 195 MPa τxy = -3.75 MPa
Q: a) Calculate the principal stresses, given that the state of plane stress for an element is: Oy =…
A:
Q: C 800 mm 18 mm dia. Rectangular bar B D 16 mm thick 25 mm 400 mm A F - F -800 mm
A: Given Data The force given is: 24 kN The height of the complee member is: 1200 mm The thickness of…
Q: Find the stress if 1002 lb force applied on 12 in2
A: Given data : Force=P Cross sectional area=A To find : Stress
Q: Calculate the normal stresses (in Pa) at point Bof the bracket caused by the 25139 N force. - 540 mm…
A:
Q: Find the principal stress at point C and D
A: The force F causes the bending moment at point C, and at point D only shear force will be there…
Q: Calculate the maximum stress in the diagram below, considering stress concentrations.
A:
Q: Calculate the maximum tensile and compression stresses in the a-a section when P = 80ON force is…
A: We are given the following data: The magnitude of the load, P=800 N
Q: Q3. Find stresses in the Bronze and Aluminum. Find the force needed to just close the gap. 1000 KN
A: NOTE:- Here, Reder must do correctionvwhile taking area from above figure because it gives in mm^2…
Q: Find the principle stresses at A if diameter is 1 inch.
A:
Q: A force 10N is applied to one end of a 10 inches diameter circular rod. Calculate the stress. 3.821…
A: Answer: The stress in the rod is 197.3525 N/m2.
Q: Find the value of force which produce stress of 1.2 N/mm2 if cross sectional area is 0.5 mm2
A: Given data : Stress=σ Area=A Find : Force
Ans: 11,708,888.89
Step by step
Solved in 2 steps with 2 images
- The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
- The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.Calculate the normal stresses (in Pa) at point Bof the bracket caused by the 23010N force. E4.png 540 mm A 1. 180 mm 180 mm B 60 mm → - 3 4 P Your Answer: -11,078,888.8888889A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 411 lbs is applied at the end of a 1.7 in lever arm, causing the pipe to twist. What is the maximum stress in the pipe in psi? 20,766.9 Correct Answer: 124,601
- Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11023 N force. E4.png 540 mm 180 mm- 1. 180 mm 60 mm → - 4 Your Answer: 6,940,407.40740741The state of stress at a point under plane stress 40 MPa, Oyy condition is Ox = = 100 MPa and Txy 40 MPa. This radius the Mohr's circle representing the given state of stress in MPa is:A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the loadings shown. Assume a = 510 mm, b = 230 mm, Px = 20 kN, P, = 16 kN, and P, = 11 kN. (a) Determine the normal and shear stresses on the top surface of the pipe at point H. (b)Determine the principal stresses and maximum in-plane shear stress magnitude at point H and show the orientation of these stresses on an appropriate sketch. a |P, y P: P H K
- If the principle stresses in a plane stress problem are 100 MPa and 40 MPa, then maximum shear stress (MPa) will be answer choices 30 20 10 100The state of stress at a point in a component is ox = -14 ksi, oy = -20 ksi, Txy-4 ksi. Sketch the state of stress at the point in x-y and the calculate the principal stresses and the magnitude of the maximum shear stress. OA = ksi OB ksi Magnitide of tmax ksi %DQuestion 2 The principal stress o1 is U -50ksi Question 3 4,356 A A NOV ksi T B 25ksi 10 ksl tv