Calculate the rate at which the average friction coefficient, friction force and heat transfer rate will change if the free flow rate of the turbulent air flowing parallel to the plate over a smooth plate is doubled. Does the result change for constant temperature and constant heat flux conditions; Please evaluate.

Calculate the rate at which the average friction coefficient, friction force and heat transfer rate will change if the free flow rate of the turbulent air flowing parallel to the plate over a smooth plate is doubled. Does the result change for constant temperature and constant heat flux conditions; Please evaluate.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.22P

See similar textbooks

Similar questions

A plate with a negligible thickness of 50 cm in width and 100 cm in length and from its upper surface, it is exposed to 2 different airflows in the same direction along its length. top of the sheet The speed of the air flowing from its surface is 3600 m/min and its temperature is 473 K. Its temperature is 298 K and its speed is 600 m/min. The total heat exchange between both fluids calculate. (Assume the initial temperature of the plate is 160⁰C.)
What are the factors that affect the value of Friction factor in Laminar flow and Turbulent flow?
A steam reservoir is covered by a rectangular plate (its length is 1 m and width 2 m). The steam temperature is 95o C, and it is in contact with the plate. Over the outside surface of the plate, water is flowing at a speed of 3 m/sec at a temperature of 25o C. What is the mean Nusselt number over the plate? What is the mean heat transfer convective coefficient over the plate? What is the heat transfer rate to the water?
Air at 20°C is hydrodynamically fully developed as it flows in a 1 cm I.D. pipe. The average velocity is 0.7 m/s. If it enters a section where the pipe wall is at 60°C, what is the temperature 0.25 m farther down stream?
For safety reasons, parts can be directly blown by air. with dimensions of 15 cmx20 cm, which are not allowed to contact printed circuit board, 20 cm long 0.2 opened inside Cold air from a rectangular hole of cmx14 cm will be cooled. from electronic parts The heat generated is transmitted from the thin layer of the card to the duct, where it is combined with the air entering the duct at a temperature of 15 °C. is removed. The heat flux on the upper surface of the channel can be considered uniform and The heat transfer from the surfaces can be neglected. If the velocity of the air in the duct does not exceed (590) m/min and the surface temperature of the duct is constant at 50 °C, this circuit board can be safely placed on it. Calculate the maximum total power of the electronic parts to be placed.
Air at 20°C enters a heated circular tube with a diameter of 50 mm and a length of 3 m. The mass flow rate is 0.005 kg/s and the flow is fully developed with h = 40 W/m2. 20°C 0.005 kg/s D q" If the tube is heated by uniform surface heat flux of 1000 W/m?, calculate the surface temperature at the outlet (Ta) in C If the surface heat flux varies linearly in the flow direction as 500x W/m2, (x is in meters and equals to 0 at the inlet and equals to 3 at the outlet) calculate the mean temperature at the outlet (Tm.o) in °C = 128 138 145 152 167 116
Consider atmospheric air at 25 °C and a velocity of 25 m/s flowing over BOTH surfaces of a 1-m- long flat plate that is maintained at 125 °C. The width of the plate (into paper direction) is 1 m. Determine the rate of heat transfer if the critical Reynolds number is 5 × 105.
The forming section of a plastics plant puts out a continuous sheet of plastic that is 1.2 m wide and 2 mm thick at a rate of 15 m/min. The temperature of the plastic sheet is 90 °C when it is exposed to the surrounding air, and the sheet is subjected to airflow at 30 °C at a velocity of 2 m/s on both sides along its surfaces normal to the direction of motion of the sheet. The width of the air cooling section is such that a fixed point on the plastic sheet passes through that section in 5 s. Draw the neat figure of the setup and determine the rate of heat transfer from the plastic sheet to the air.
Air flows hydrodynamically and thermally fully developed at an average speed of 0.5 m/s through a thin-walled pipe with a diameter of 2.5 cm. Air can be heated in two different ways. In the first, the air can be heated at a constant surface temperature by means of a steam from the outside of the pipe, and in the second with an electric heater (thus providing a constant heat flux). Calculate the heat convection coefficients for both heating methods. According to this; Given: Properties of air at 350°K: υ= 20.76.10-6 m2/s, k =0.03 W/mK, Pr=0.70
Hot air at atmospheric pressure and 85°C enters a 10-m-long uninsulated square duct of cross section 0.15 m * 0.15 m that passes through the attic of a house at a rate of 0.1 m3/s. The duct is observed to be nearly isothermal at 70°C. Determine the exit temperature of the air and the rate of heat loss from the duct to the air space in the attic. Evaluate air properties at a bulk mean temperature of 75°C. Is this a good assumption?
Q3) Engine oil at 80°C flows over a flat surface at 40°C for cooling purpose, the flow velocity being 2 m/s. Determine at a distance of 0.4 m from the leading edge the hydrodynamic and thermal boundary layer thickness. Also determine the local and average values of friction and convection coefficients.
Air stream at 1 atm flows with a velocity of 2 m/s, in parallel over a 3 m long square flat plate, placed on ground, where there is an unheated starting length of 1 m. The air stream has a temperature of 20 °C and the heated section of the flat plate is maintained at a constant temperature of 80 °C. Determine the local heat transfer coefficient at trailing edge and average convection heat transfer coefficient for the heated section. Also calculate the heat loss by convection. Determine the average friction coefficient and wall shear stress and drag force.