Calculation/Enumeration. Present the complete solution for each problem. (4 x 20% = 80%) I. SITUATION 1 The steel grating 3.20 meters x 3.20 meters placed on top of the concrete manhole is composed of 3 mm x 25 mm flat bars at 150mm on centers both ways enclosed by an angle bar 30mm x 30mm x 6mm thick. a. Find the total requirement of steel bars in kilograms per set, if the density of the steel is 7,850 kilograms per cubic meter. Answer is W=_ in kilograms. FIGURE 1 STEEL GRATING Note: 1meter = 1,000millimeters, Consider the density of steel = 7,865 kilograms/cubic meter. 3mm x 25mm FLAT BAR 30mm x 30mm x 6mm ANGLE BAR %3D

Calculation/Enumeration. Present the complete solution for each problem. (4 x 20% = 80%) I. SITUATION 1 The steel grating 3.20 meters x 3.20 meters placed on top of the concrete manhole is composed of 3 mm x 25 mm flat bars at 150mm on centers both ways enclosed by an angle bar 30mm x 30mm x 6mm thick. a. Find the total requirement of steel bars in kilograms per set, if the density of the steel is 7,850 kilograms per cubic meter. Answer is W=_ in kilograms. FIGURE 1 STEEL GRATING Note: 1meter = 1,000millimeters, Consider the density of steel = 7,865 kilograms/cubic meter. 3mm x 25mm FLAT BAR 30mm x 30mm x 6mm ANGLE BAR %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1\ A copper bar consists from three sections: sections 1 is of 25 mm diameter and 60 mm long, section 2 is of 15 mm diameter and 50 mm long and section 3 is 20 mm square and 40 mm long. The bar is subjected to an axial tensile load which induces a stress of 20 MN/m' on the smallest cross section. Determine the total increase in the length of the bar when the load is applied. For copper E=100 GN/m2.
1 Rigib bar AB; attached to two vertical rods as shown, Is horizonta before the lead P is applied. If is load P = 12 kips, determine it's vertical movement." Aluminum L= 13 Ft A=0.775 in E=1.015×10 lb in² 10 Ft 6.5 + p steel L=10m A = 0.465 sq. in € = 2.901 x 107 psi
1. Two A36 16mm thick steel plates are connected by four rivets shown. 1:11 Pu a. Calculate design strength in KN considering tension failure on gross section yielding. b. Calculate design strength in KN considering tension failure on net section fracture. c. Calculate design strength in KN considering block shear rupture. f. Calculate the ultimate safe load "P" in KN. Given: 500 X =175mm Rivet Dia.=20mm Y=200mm Fy=248Mpa Fu=40 Mpa Bolt Dia.=22mm
The lower ends of the 3 bars in the figure are at the same level before the rigid homogenous 18Mg block is attached. Each steel bar has an area of 566mm^2 and E=200Gpa. For the bronze barn the area is 866mm^2 and E=83Gpa. Find the stresses developed in each bar.
The drill is jammed in the wall and is subjected to the torque and force shown in a 20 N-m O A 125 mm = B 400 mm -5 mm Section a-a Part A Determine the normal stress at point A on the cross section of drill bit at section a-a. 150 N Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: Tap image to zoom ANSWER: ((Txy)V) A = Part B Determine the transverse stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units.
PLEASE WRITE LEGIBLY WITH COMPLETE SOLUTION SN= 77 MN= 68
Find the x and y Guided Problem (first c): Use the appropriate trig functions to get the x and y components Compare your answers: Fx = -600lb, Fy = +1039.2lb Standard Problem (second c) ● X- components of the forces below: 1200 lb 30⁰ Y O (c) Y -X X- 3 kips 3 Y (c) Y X
A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and 3 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 60 kips tension in the x direction, 70 kips compression in the y direction, and 45 kips tension in the z direction. If v = 0.30 and E = 29x10^6 psi. Determine: - - - - Areas in the X, Y, and Z Direction Stresses in the X, Y, and Z Direction Normal Strain in the X, Y, and Z Direction Elongation in the X, Y, and Z Direction Single Uniformly Distributed Load in the X Direction that would produce the same deformation in the Z Direction as the Original Loading Px = : 60 kips Pz = 45 kips Py = 70 kips X 4 in Py = 70 kips Pz = 45 kips y 2 in 3 in Z Px = 60 kips
Problem 4.8 The truss is made of three A-36 steel members, each having a cross-sectional area of 400 mm². Part A Determine the magnitude P required to displace the roller to the right 0.28 mm. Express your answer to three significant figures and include appropriate units. Di Submit μA P = 0.09224 mm Previous Answers Request Answer ? 0.8 m 0.8 m - 5 kN 0.6 m-
b. Calculate "P" in KN considering tension failure on net area Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
and show the stress acting on a small element of material at point A of the shaft, and points B and C of the tube. Misan 10.5 These lectare notes may NOT be used, rependuced, or distibuoted in any form without a prior permission from the instructor. Mechanics of Materials: 2019-2020 Dr. Mustafa Chasib Jasim University of Misan College of Engineering/Department of Civil Engineering Assignment Problem 10.1. A steel bar of diameter d = 52 mm is twisted by torques at the ends. The allowable shear stress is 65 MPa. What is the maximum torque that can be applied? Problem 10.2. A stepped steel shaft with diameters d, = 56 mm and d = 52 mm is twisted by torques T, = 2.5 kN.m and T = 1.5 kN.m acting in opposite directions. What is the maximum shear stress? Misan University 10.6 These lecture nntes may NOT he used, rependaced, or distributed in any form without a prinr permiinn from the instractor.
A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate shears at a stress of 310 MPa, determine the minimum force P required to punch the slot. Punch 705 kN 660 kN 844 KN 904 kN O 772 KN Slug Plate 20 mm 75 mm Plan view of slug Que Nume Blank Que Nume Blank Que Nume Blank Que Nume Blank Que Nume Blank View Que Multi Que Multip Que