Chose True or False * True False If a system is subjected to step input, the type of static error coefficient performs the function of controlling steady state error is position. If a type 1 system is subjected to parabolic input, the value of steady state error will be zero . The elements of rotational motion are the Mass, Spring, Friction. the notation represents the feedback path in closed loop system is c(t). The output signal is fed back at the input side from the Summing point. In an integral controller the output is proportional to integral of input. Two loops are said to be non- touching only if no common Branch exists between them. In block diagram representation, the lines connecting the blocks, known as branches. Order of the system can be determined from the e forward path transfer function of the system. A system with transfer function 1/Ts+1, subjected to a unit step input to reach 63.2% of final value, The value of t is T/2.

Chose True or False * True False If a system is subjected to step input, the type of static error coefficient performs the function of controlling steady state error is position. If a type 1 system is subjected to parabolic input, the value of steady state error will be zero . The elements of rotational motion are the Mass, Spring, Friction. the notation represents the feedback path in closed loop system is c(t). The output signal is fed back at the input side from the Summing point. In an integral controller the output is proportional to integral of input. Two loops are said to be non- touching only if no common Branch exists between them. In block diagram representation, the lines connecting the blocks, known as branches. Order of the system can be determined from the e forward path transfer function of the system. A system with transfer function 1/Ts+1, subjected to a unit step input to reach 63.2% of final value, The value of t is T/2.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 5RQ: What are interpoles, and what is their purpose?

See similar textbooks

Similar questions

Shown in the figure below is an electrical circuit containing three resistors and two batteries. R1 10 R2 I2 R3 Write down the Kirchhoff Junction equation and solve it forI, in terms of J, and I. Write the result here: Write down the Kirchhoff Loop equation for a loop that starts at the lower left comer and follows the perimeter of the circuit diagram dockwise. Write down the Kirchhoff Loop equation for a loop that starts at the lower left comer and touches the components 4V, R, and Rg. The resistors in the circuit have the following values: . R,70 • R=10 Solve for all the following (some answers may be negative): Amperes Amperes Amperes
4_ For the system shown in figure N°4, find the percentage overshoot, the settling time, the peak time and the rising time for a unit step input if the response is underdamped. Is it muffled? Say why? Construct the graph of the answer c(t).
QUESTION 5 Consider the closed-loop system in the figure below R(s) + K Give your answer correct to two decimal places. S a where k-22. Find the steady-state value of the error when the reference is a ramp function R (s) = 7/9 with a= 14. Y(s)
Trial example of how to use Kirchhoff analysis to determine the initial current in each section along with its direction and the potential difference across the load
The characteristic equation of sixth order system is as below find the stability of system. + 2s° + 8s4 + 12s + 20s? + 16s + 16 = 0
Q5: A closed loop system is shown in Figure Q5: K U(s)- Y(s) s(s+2) 1+ as Figure 05 1- Determine the value of K and a so that the maximum overshoot is 0.20 and settling time (2% criterion) is 4 sec to a unit step input. 2- Determine the peak time for a unit step input and the steady state error for a ramp input. 3- What would be the value of a to attain critical damping (assume K = 1).
Shown in the figure below is an electrical circuit containing three resistors and two batteries. R3 10 R2 R1 Write down the Kirchhoff Junction equation and solve it for I, in terms of I, and Iz. Write the result here: Write down the Kirchhoff Loop equation for a loop that starts at the lower left corner and follows the perimeter of the circuit diagram clockwise. Write down the Kirchhoff Loop equation for a loop that starts at the lower left corner and touches the components R1, R2, and 4V. The resistors in the circuit have the following values: R, = 130 • R2 = 50 R3 = 10 Solve for all the following (some answers may be negative): | Amperes I = I, = Amperes Iz = Amperes NOTE: For the equations, put in resistances and currents SYMBOLICALLY using variables like RR2,R3 and I,,12,13. Use numerical values of 10 and 4 for the voltages.
2. Consider the system given below. Investigate the stability using describing function. Find nature, amplitude and frequency of limit cycle. S 性 1 $+4 s+2
Write a Note on use of ODE in solving series RL circuit. Using Kirchhoff's voltage law find ordinary differential equation (ODE) representing system of series RL circuit. Solve that ODE and find out function for current i. Do detailed Curve Sketching analysis (Domain, Intercepts, Symmetry, Asymptotes, Intervals of Increase or Decrease, Local maximum and minimum, Concavity and points of Inflection, Sketch the function/ Plot the graph) of it (function for current 'i'). a. Following is the description of an RL circuit: constant voltage V = 5 V, R = 50 Q, L = 1 H, initial current i = 0 Amp. Calculate i' at any time t in RL circuit. Show equation for transient current. Calculate steady state current.
The problem is to find the primary voltage required, but I already got a solution. The points is in this part (picture below), I don't know how solve involving the angular like (-36.86°). Can you explain how to solve involving an angle?
Parts D-F please show work, thank you :)
plz solve only part 2 Your company is considering the installation of a 2 MW wind turbine with a rotor diameter of 80 m in a location with average wind v = 10 m/s. The turbine has a cut-in velocity of 5 m/s and a cut-out velocity of 25 m/s. The capacity factor is 0.45. The installed cost of the turbine is $3,500,000. Operating expenses are $225,000 per year. The system has a power coefficient (electric power generated divided by wind power) of 0.45. part 1) What price would you have to get for the electricity you produce to obtain a 10% return on the plant investment assuming a project lifetime of 20 years? Use the tables for the cumulative wind power distribution in the notes on wind probability to answer this question. Assume an air density of 1.225 kg/m3. The answer is equal to 0.0815 dollar part2) How would your answer to problem one change for each of the following modifications to the data in that problem? (Consider each change independently, not as a cumulative series…