Compute the coordinates of the centroid (, g) of the area shown. d C a Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 47 mm 25 mm 24 mm d 102 mm The x coordinate of the centroid is a = mm. The y coordinate of the centroid is y mm.

Compute the coordinates of the centroid (, g) of the area shown. d C a Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 47 mm 25 mm 24 mm d 102 mm The x coordinate of the centroid is a = mm. The y coordinate of the centroid is y mm.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.43P

See similar textbooks

Similar questions

Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your answer should have 0 decimal places needed. Ex: 76,440 10 - 30 B
Question 3 Make an Isometric Drawing of the support bracket shown in Figure 4. Take the dimension 'H' as 35 mm. As per standard instruction for pictorial views in ENG1100, no dimensioning is required. Orientate the drawing so View A' of Figure 4 is in the direction of the shaded face of the representative isometric view of a cube shown in Figure 3 with the top of the 'View A' orientated towards TOP' as shown in Figure 3. Top Figure 3 140 22 DRILL 96 - 22 22R 16 41 198 40 - 5/ 51- 16- 19R 16 DRILL-3HOLES 51- View A Figure 4: Support Bracket (Source: Boundy AW, Engineering drawing, 8th edn, McGraw Hill, dimensions altered)
2. For the plan area shown, determine the location of the Centriod. Use you're the last two digits of your ID for the missing length x mm. ID:88 The following table facilitates the calculations for the required data 5 mm 10 mm 3 mm 10 mm x mm
Exercise 1 Tabulate the absolute coordinates. Write a program to drill the holes and mill the rectangular pocket. Exercise 2 20 30 60 80 4x02 x 5 deep 2 Material: Square Pocket: 5mm deep Tool change at: XO, YO, Z 25 15mm thick Plastic 3 plno
1- Determine the location y of the centroid C of the beam having the cross-sectional area shown 150 mm 150 mm • Examaly 20 mm 20 mm B 150 mm 150 mm 15 mm 10 mm -15 mm 83 m 10 mm The missing data is 83 mm NB: each student inputs the missing data (in red dashed-line). The missing data is the last two digits of your ID number. If your two last-digits number is smaller multiply by 10 (example if you get 19 →19x10 = 190)
In the crank-slider shown, OA = 5 cm, AB = 15 cm and the offset e angle a at which slider B reaches the extreme right position. Write your answer in degrees but do not write the unit. 7 cm. Find the value of 7777 x. Answer: DELL
Rotate the objects shown below by the indicated amount and sketch the result in the space provided. You do not need to include the coordinate axes in your sketch.
Write the first trigonometric function in terms of the second for 0 in the given quadrant. tan(0), cos(0); 0 in Quadrant II tan(0) =
Consider the figure
Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A = 65 B = 43 A 40 B-30 10 30 40 B
The below figure shows two views of a bolster block. Draw, using 1 st angle projection and a suitable scale, the following views: (a) the given front elevation; (b) a sectional end elevation taken on the cut-ting plane A-A; (c) the given plan; (d) an isometric view of the block. Show all hidden details. Print title, scale and show six leading dimensions Note : use creo parametric to solve the answer
The square deforms into the position shown by the dashed lines. (Figure 1) The dimensions are S = 55 mm, S' = 60 mm, Az1 = 5 mm, and A₂ = 8 mm. Side D'B' remains horizontal. Figure 91.5 ATL Ax₂ 1 of 1